An AC voltage source delivers current to Load A and Load B which are connected in parallel. Current in Load A is 25 A and Current in Load B is 42.2. If the current in load B leads the current in load A by 45 degrees, calculate: a) Resultant or total current, b) Angle between the resultant current and Load current A if Load Current A is at reference or zero degrees

An AC voltage source delivers current to Load A and Load B which are connected in parallel. Current in Load A is 25 A and Current in Load B is 42.2. If the current in load B leads the current in load A by 45 degrees, calculate: a) Resultant or total current, b) Angle between the resultant current and Load current A if Load Current A is at reference or zero degrees

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Discuss thr impact of wind energy on power system
a.) How the improvement of the power factor decreases the line losses in the AC distribution system and increases the capacity of power transfer in the existing distribution system. Explain with the help of the figure. b.) What is the effect of power factor improvement on the DC distribution system? Draw a basic architecture of the AC and DC distribution system.
Objective 3 ) -Be able to calculate all forms of ac power in ac circuits with linear transformers and ideal transformers
The Dc value of a pure Ac voltage source is zero Select one: True False
1) Principle and features of different methods for measuring three-phase power. 2) Discuss the formula of Total Power and Power Factor in a three-phase AC circuit.
Two transformers A and B give the following test results. With the low-tension side short-circuited, A takes a current of 10 A at 200 V, the power input being 1000 W. Similarly, B takes 30 A at 200 V; the power input being 1,500 W. On open circuit, both transformers give a secondary voltage of 2200 when 11,000 volts are applied to the primary terminals. These transformers are connected in parallel on both high tension and low-tension sides Calculate the current and power in each transformer when supplying a load of 200 A at 0.8 power factor lagging. The no-load currents may be neglected (Hint: Calculate ZA and ZB from S.C. test data) Answer [LA = 50.5 A, PA = 100 kW; IB = 151 A, PB = 252 kW] Please answer in typing format please
A 20-kVA, 507 V load is to be supplied by an ideal step-up autotransformer from a 400-V source. Find the current in the common winding. Use two decimal places for final answer if necessary.
Two transformers A and B give the following test results. With the low-tension side short-circuited, A takes a current of 10 A at 200 V, the power input being 1000 W. Similarly, B takes 30 A at 200 V the power input being 1,500 W. On open circuit, both transformers give a secondary voltage of 2200 when 11,000 volts are applied to the primary terminals. These transformers are connected in parallel on both high tension and low tension sides Calculate the current at transformer B when supplying a load of 200 A at 0.8 power factor lagging. Hint : Calculate ZA and ZB from S.C. test data) Answer in whole number
5.In three-phase transformers, the high voltage star connection is preferred. This is so because in this case A) The voltage on the star windings is lower than if they were in delta and this reduces manufacturing costs. B) The voltage on the star windings is higher than if they were in delta and this reduces manufacturing costs. C) The voltage on the star windings would be the line-to-line voltage of the system since it is a three-phase manufacturing transformer. D) THERE IS NO SOLUTION
Estimate the balance conditions for an AC bridge? illustrate it in ONE (1)equation.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Solve for the following Requirements Load Voltages Line Currents Source Complex Power