a) Consider a three-phase power supply with associated electrical loads as shown in Figure Q4. State, giving reasons, whether this represents a star or delta load configuration. Also explain why a neutral conductor is not required for this system and what advantages that may have. 30 Q 125 mH 50 Hz three phase supply 30 0 30 Q

a) Consider a three-phase power supply with associated electrical loads as shown in Figure Q4. State, giving reasons, whether this represents a star or delta load configuration. Also explain why a neutral conductor is not required for this system and what advantages that may have. 30 Q 125 mH 50 Hz three phase supply 30 0 30 Q

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Describe the concept of three-phase power in electrical systems and its advantages over single-phase power.
Discuss the role of FACTS (Flexible Alternating Current Transmission Systems) devices in power system control and optimization.
4) State the relation between line and phase values of voltage and current for 3-pha se DELTA connected load .state the equation for active, reactive power consumed by 3-phase load.
Each line of a 3-phase system given in figure is suspended by a string of 5 identical disks and the ratio of C1/C=0.1 (Shunt capacitance per self-capacitance) is given. If the string is connected to line of voltage 33kV. a) What is the voltage distribution over the unit of string and what is the string efficiency? b) When the string is supplied by a Guard Ring and this lead to add a two air capacitance of value 0.2C, 0.1C respectively to the nearest to the conductor. Find the new voltage distribution and the new efficiency.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.iii) Assuming that the post fault condition is small disturbance stable and that thereis no negative interaction among system controllers, calculate the criticalclearing angle, σcr, at which the fault should be cleared to ensure the generatorreaches a new steady…
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.
please explain the operating principle of single phase 2S-2P PMSM based on 3D design illustration.
⦁ Does transformers work on DC? Justify your answer.
What is voltage stability? How is reactive power linked with the voltage stability in the power system? Write down the effect of ‘Load Tap Changer (LTC)’ on voltage stability and analyze very briefly using P-U (nose) curve.