An aircraft is flying straight and level at a certain altitude with a velocity of 214 fps. Determine the power required if the wing area is 115 ft? and the total drag coefficient is 0.067. Assume SSLC (p=0.002377 slug/ft3). Provide answer in ft-Ib/s. and round off to the nearest whole number. Solve using standard English units.

An aircraft is flying straight and level at a certain altitude with a velocity of 214 fps. Determine the power required if the wing area is 115 ft? and the total drag coefficient is 0.067. Assume SSLC (p=0.002377 slug/ft3). Provide answer in ft-Ib/s. and round off to the nearest whole number. Solve using standard English units.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.26P

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
13.94. A body travels through 60° standard air at 60 mph, and 5.5 hp is required to maintain this speed. If the projected area is 13.5 ft2 , find the drag coefficient. Ans. 0.28
How does a winglet on the wing tip reduce induced drag? Which drag is higher if an aircraft is flying at 100knts and the L/Dmax is 120knts? How do you know this?
A commercial airplane has a total mass of 70,000 kg and a wing planform area of 150 m2. The plane has a cruising speed of 558 km/h and a cruising altitude of 12,000 m, where the air density is 0.312 kg/m3. The plane has double-slotted flaps for use during takeoff and landing, but it cruises with all flaps retracted. Assuming the lift and the drag characteristics of the wings can be approximated by NACA 23012 , determine (a) the minimum safe speed for takeoff and landing with and without extending the flaps, (b) the angle of attack to cruise steadily at the cruising altitude, and (c) the power that needs to be supplied to provide enough thrust to overcome wing drag.
A jet airplane weighs 160,000 N and has a zero-lift drag coefficient of 0.008 and a wing area of 42 m^2. At 100 m/s at sea level, the rate of climb is 11.5 m/s. The thrust developed by the engines is equal to 27,000 N. Determine the maximum rate of climb and the corresponding flight speed at sea level .
A commercial airplane has a total mass of 150,000 lbm and a wing planform area of 1700 ft2. The plane has a cruising speed of 625 mi/h and a cruising altitude of 38,000 ft where the air density is 0.0208 lbm/ft3. The plane has double-slotted flaps for use during takeoff and landing, but it cruises with all flaps retracted. Assuming the lift and drag characteristics of the wings can be approximated by NACA 23012, determine (a) the minimum safe speed for takeoff and landing with and without extending the flaps, (b) the angle of attack to cruise steadily at the cruising altitude, and (c) the power that needs to be supplied to provide enough thrust to overcome drag. Take the air density on the ground to be 0.075 lbm/ft3.
The drag coefficient of a car at the design conditions of 1 atm, 70°F, and 60 mi/h is to be determined experimentally in a large wind tunnel in a full-scale test. The frontal area of the car is 22.26 ft2. If the force acting on the car in the flow direction is measured to be 68 lbf, determine the drag coefficient of this car.
, A small aircraft has a wing area of 40 m2a lift coefficient of 0.45 at takeoff settings, and a total mass of 4000 kg. Determine (a) the takeoff speed of this aircraft at sea level at standard atmospheric conditions, (b) the wing loading, and (c) the required power to maintain a constant cruising speed of 360 km/h for a cruising drag coefficient of 0.035.
An airplane has a mass of 50,000 kg (without load), a wing area of 360 m2 , a maximum lift coefficient of 3.25, and a cruising drag coefficient of 0.03 at an altitude of 12,000 m. Taking the density of standard air as ρ1 = 1.225 kg/m3 at sea level and ρ2 = 0.312 kg/m3 at 12,000 m altitude. (a) Generate a plot of the safe takeoff speed at sea level Vs the load carried by airplane (ranging from 0 kg to 20,000 kg of load). (b) Determine the power that must be delivered by the engines for a cruising speed of 800 km/hr.
A small aircraft has a wing area of 37 m2, a lift coefficient of 0.45 at takeoff settings, and a total mass of 4300 kg. Determine the following: The takeoff speed of this aircraft at sea level at standard atmospheric conditions The wing loading The required power to maintain a constant cruising speed of 300 km/h for a cruising drag coefficient of 0.036
Q1/ Boeing 737 - 60 flies at altitude 15000m above sea level with speed 85 m/s and total drag coefficient equal to ( 5) . Find the drag force at this fly condition. Given data IR=287,g=9.81 m/s2 , rho O=0.3648 kg/m2 and wing area = 120m^ ^ 2^ *
Kindly give me both right solutions with clear calculations The drag polar of a glider is given by CD=0.01+0.022CL2 . If it is launched from a height of 400m in still air. Please determine:(a) the maximum lift to drag ratio ??;(b) the greatest possible ground distance it can cover.