An airplane has a half-wingspan of 35 m. Determine the change in length (mm) in mm of the aluminum alloy [Coefficient of Thermal Expansion = 22.5x10-6/°C] wing span if the plane leaves the ground at a temperature of 15°C and climbs to an altitude where the temperature is -51 °C. Note: Add minus sign if change in length is a contraction. Use 2 decimals

An airplane has a half-wingspan of 35 m. Determine the change in length (mm) in mm of the aluminum alloy [Coefficient of Thermal Expansion = 22.5x10-6/°C] wing span if the plane leaves the ground at a temperature of 15°C and climbs to an altitude where the temperature is -51 °C. Note: Add minus sign if change in length is a contraction. Use 2 decimals

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 3P: An astronaut has a mass of 68 kg. What is the weight of the astronaut on Earth at sea level? What...

See similar textbooks

Similar questions

An astronaut has a mass of 68 kg. What is the weight of the astronaut on Earth at sea level? What are the mass and the weight of the astronaut on the Moon, and on Mars? What is the ratio of the pressure exerted by the astronauts shoe on Earth to Mars?
A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
The 700-N force is applied to the 100-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. Explain whether the block moves or not? If it moves, calculate the kinetic force.
A frame shown in the figure consists of a horizontal rigid bar that is supported by two concrete columns. The temperature of system is increased by ΔT= 90 °C. Assume α1 = 7.5 x10-6/°C, α2 = 13 x10-6/°C, a = 290 mm, and L = 270 mm Determine the angle of rotation if the temperature of system is increased by ΔT? In micro rad
A mass of 3.0kg is projected with a speed of 5.6m/s up a plane inclined 33 degrees with the horizontal. If coefficient of kinetic friction is 0.21, determine the distance it will travel before it stops.NOTE: use 3 decimal places
A mass of 3.9kg is projected with a speed of 4.7m/s up a plane inclined 38 degrees with the horizontal. If coefficient of kinetic friction is 0.27, determine the distance it will travel before it stops. Note: use 3 decimal places
In the given figure, W= 200kg. Assume that the coefficient of friction between surfaces is 0.40. Which of the following most nearly gives the reaction between the block and the wall if the block is raised due to the applied force P?
A fluid storage tank is fixed to the wall as shown in the figure. Considering the unit width (into the page) of the container, a) Determine the reaction at the fixed support. Neglect the thickness and weight of the container. h (oil) = 0.53 m h (water) = 1.41 m h (mercury) = 0.71 m L = 3.0625 m
A steel tape of nominal length 200 m with a plumb bob of mass 16 kg attached to it was used to measure a length down a shaft as 160.852 m. The mean temperature during the measurement was 4 C. If the tape was standardized to be 200.0014m under a tension of 115 N at 20" C temperature, determine the correct measured length. The following data may be used: Mass of tape = 0.07 kg/m Cross-sectional area of tape= 10 mm Coefficient of linear expansion a = 11x 10/°C Modulus of clasticity = 2x 10° Nmm Acceleration due to gravity 9.807 m's.
Calculate the energy required to lift an elevator and its occupants with amass of 2000 kg for the following situations: (a) between the first and thesecond floor, (b) between the third and the fourth floor, (c) between the firstand the fourth floor. (as shown .) The vertical distance between eachfloor is 4.5 m. We can use as shown to analyze this problem; the energy required to lift the elevator is equal to the change in its potential energy, starting with
Calculate the capillary effect in millimeters in a glass tube of 4mm diameter, when immersed in Water Mercury the temperature of the liquid is 200C in contact with air are 0.073575 N/m and 0.51 N/m respectively. The angle of contact for water is zero and that for mercury is 1300. Take density of water at 200C as equal to 998 kg/m3. Explain the ways of describing the fluid motion
Calculate the pressure decrease (in psi) when you climb from an elevation of 660 ft to a mountain top 1640 ft above mean sea level. Assume that the unit weight of air is constant at 0.07967 lb/ft^3.