Using the maximum distortional energy theory and the stress concentration figures given in section 4.12, find the maximum diameter of the radial hole (d) for a safety factor of n = 1.8. The torsion applied to the shaft is T = 400 Nm, the diameter of the shaft is D 30 mm and the yield strength of the material is Sy = 460 MPa. Based on the stress concentration figure, assume an initial K₁ value and then revise your solution once you have determined an initial d. = T T

Using the maximum distortional energy theory and the stress concentration figures given in section 4.12, find the maximum diameter of the radial hole (d) for a safety factor of n = 1.8. The torsion applied to the shaft is T = 400 Nm, the diameter of the shaft is D 30 mm and the yield strength of the material is Sy = 460 MPa. Based on the stress concentration figure, assume an initial K₁ value and then revise your solution once you have determined an initial d. = T T

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.6P: Two line loads q1 and q2 of infinite lengths are acting on top of an elastic medium, as shown in...

See similar textbooks

Similar questions

The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
A cylindrical tube of constant wall thickness t and inside radius r ¼ 10t carries a torque T. Find the expression for the maximum shear stress in the tube using (a) the torsion formula for a hollow shaft in Eq. (3.5d); and (b) the thin-walled tube formula in Eq. (3.8b). What is the percentage error in the thin-walled tube approximation? Please show complete solution. Thank you!
A cylindrical tube of constant wall thickness t and inside radius r ¼ 10t carries a torque T. Find the expression for the maximum shear stress in the tube using (a) the torsion formula for a hollow shaft in Eq. (3.5d); and (b) the thin-walled tube formula in Eq. (3.8b). What is the percentage error in the thin-walled tube approximation? Please show complete solution and explain. Thank you.
The vertical stress at point P1 due to the point load Q on the ground surface as shown in figure is sigma_{z} According to Boussinesq's equation, the vertical stress at point P2 shown in figure will be
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 57 kN/m2. Both stresses are principle stress. (a) Draw the Mohr circle that describes the 2D stress state at the point. (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 532 mm2 and P= 35.29 kN. Round off the final answer to four decimal places.
state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
Find the stresses in a medium with a cylindrical hole under the action of radial tension or compression by the stress oo and the internal pressure p. Determine the stress concen tration coefficient. How does the stress concentration coefficient and stress distribution depend on the radius of the cavity?
Determine the magnitude of the maximum in-plane shear stress at point A (in MPa).