An airplane is traveling in the direction 25° west of north at 400 km/hr. Find the component form of the velocity of the airplane, assuming that the positive x-axis represents due east and the positive y-axis represents due north. What is the component form of the velocity of the airplane? (Round the final answer to one decimal place as needed.)

An airplane is traveling in the direction 25° west of north at 400 km/hr. Find the component form of the velocity of the airplane, assuming that the positive x-axis represents due east and the positive y-axis represents due north. What is the component form of the velocity of the airplane? (Round the final answer to one decimal place as needed.)

Trigonometry (MindTap Course List)

8th Edition

ISBN:9781305652224

Author:Charles P. McKeague, Mark D. Turner

Publisher:Charles P. McKeague, Mark D. Turner

Chapter3: Radian Measure

Section3.5: Velocities

Problem 61PS: A gear train consists of three gears meshed together (Figure 9). The middle gear is known as an...

See similar textbooks

Similar questions

Considering that the consecutive dials on the natural gas meter rotate in opposite directions, what is the current reading in cubic feet of usage? The initial direction is clockwise.
The second hand of a clock is 8 centimeters long. Find the linear speed of the tip of the second hand as it passes around the clock face.
Solve the following exercises based on Principles 18 through 21, although an exercise may require the application of two or more of any of the principles. Where necessary, round linear answers in inches to 3 decimal places and millimeters to 2 decimal places. Round angular answers in decimal degrees to 2 decimal places and degrees and minutes to the nearest minute. Points A, B, C, D, and E are tangent points. a. If AB=46.00 and DE=66.00 , find 1. b. If AB=53.00 and DE=70.00 , find 1.
A gear train consists of three gears meshed together (Figure 9). The middle gear is known as an idler. Show that the angular velocity of the third gear does not depend on the number of teeth of the idler gear (Gear 2).
Sketch the curve represented by each set of equations by eliminating the parameter. a. x=5cos and y=3sin,02 b. x=1+tan and y=2+2sec,/23/2
Solve the following exercises based on Principles 18 through 21, although an exercise may require the application of two or more of any of the principles. Where necessary, round linear answers in inches to 3 decimal places and millimeters to 2 decimal places. Round angular answers in decimal degrees to 2 decimal places and degrees and minutes to the nearest minute. Three holes are to be located on the layout shown. The 72.40-mm diameter and 30.80-mm diameter holes are tangent at point T, and TA is the common tangent line between the two holes. Determine (a) dimension C and (b) dimension D.
Solve the following exercises based on Principles 18 through 21, although an exercise may require the application oftwo or more of any of the principles. Where necessary, round linear answers in inches to 3 decimal places and millimeters to 2 decimal places. Round angular answers in decimal degrees to 2 decimal places and degrees and minutes to the nearest minute. a. If AB=7218 and CD=5024 find: (1) 1 (2) 2 (3) 3 b. If CD=4315 and AD=10605 , find: (1) 1 (2) 2 (3) 3
Solve the following exercises based on Principles 18 through 21, although an exercise may require the application of two or more of any of the principles. Where necessary, round linear answers in inches to 3 decimal places and millimeters to 2 decimal places. Round angular answers in decimal degrees to 2 decimal places and degrees and minutes to the nearest minute. a. If 1 = 6700' and 2 =9300', find: (1) AB (2) DE b.If 1 = 7500' and 2 =8500', find: (1) AB (2) DE