An alternate voltage signal with a root mean square value of 1.57 V, which is superimposed to a direct voltage of -4 V, is connected to the input of a true-RMS multimeter that is AC coupled. What is the reading of the multimeter when the ACV (alternate voltage) function is selected? 718 (a) -2.43 V (b) -4.0 V (c) 2.43 V (d) 1.57 V 0261

An alternate voltage signal with a root mean square value of 1.57 V, which is superimposed to a direct voltage of -4 V, is connected to the input of a true-RMS multimeter that is AC coupled. What is the reading of the multimeter when the ACV (alternate voltage) function is selected? 718 (a) -2.43 V (b) -4.0 V (c) 2.43 V (d) 1.57 V 0261

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitance and resistance should be connected in series with the coil if the power input to the latter is to remain unchanged and the overall power factor is to be unity (in resonance)? The circuit is energized by a 120 volt, 60 cps source. 2. The given figure is to be designed to pass a wave having a frequency of 3500 cps and block a 2500 cps wave. The series inductor has an inductance of 0.0023 henry. Calculate the capacitance of the series capacitor and the parallel inductor.
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
The root mean square (or RMS) is anothermeasure of average value, often used with oscillating functions(for example, sine and cosine functions that describe the current,voltage, or power in an alternating circuit). The RMS of a function ƒ on the interval [0, T] isCompute the RMS of ƒ(t)= A sin(Ѡt), where A and v arepositive constants and T is any integer multiple of the period ofƒ, which is 2∏/Ѡ.
Derive the following. Assume an ideal current source a.) Frequency Response
A 29-Ω television and an 16-Ω amplifier are connected in series across a 158-V source of voltage from an outlet. A 34-Ω light bulb is also connected across the 133-V source and is in parallel with the series combination. (a) Determine the total rms current supplied by the voltage source. A (b) Determine the total average power supplied by the voltage source.
The graph of the vs sign applied to the circuit in the figure is given above. The switch works ideally in the circuit Switch; When the applied input signal is positive, it becomes closed. Current flows through it) In the applied input signal, Vp = 12V, R = 10ohm, T = lms. According to this; a) Find the mean and rms values of the output voltage? b) Find the average input power and output power and calculate its efficiency. c) If we consider that there is a voltage drop of 1V on the switch; c.1) Calculate the average and rms values of the output voltage, c.2) Average input power and output power c.3) Efficiency.
2. Write an OCTAVE program to plot the signal given below P=Pmax Sin(2πft); where Pmax=10 MW, f=60 Hz Find out time.peniod and verify it with graph. Assume necessary data.
In the circuit given below, Ra=Rb=Rc=9 ohm loads are fed with an AC voltage with a fundamental frequency of f=30Hz. The power value drawn from the source was measured as PK=5512.50 watts. Each switching element is triggered to be 120 degrees conduction. Calculate the effective values of the voltage Vab and the current flowing through the S1 switching element Vab_rms=, Ls1_rms?
The given data to be used for getting the RMS Values is 0, 5, 10, 30, 50, 70, 50, 30, 10, 5, 0, -5, -10v. Find the RMS value.
The input signal to an audio amplifier is describedby vI = (0.5 + 0.25 sin 1200πt) V, and the outputis described by vO = (2 + 4 sin 1200πt +0.8 sin 2400πt + 0.4 sin 3600πt) V. What is thevoltage gain of the amplifier? What order harmonicsare present in the signal? What is the total harmonicdistortion in the output signal?
Electronic Since k = 0.35x10^3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 21 kΩ in the circuit in the figure, the output voltage In which option is the amplitude value (Vout) given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency.