The L-shaped beam AB is resting on a smooth surface at A and supported by the collar at B which in turn is resting on a smooth rod built into the floor and wall supports as shown in Fig 3. Four loads and two moments of couples act on the beam as shown in Fig. 3. Calculate the reactions at the supports A and B. Neglect the thickness of the beam. 3. 250 N 500 N 30 3 m 4 m 4 m 3 m 40° 0.5m 250 Nm 2 m 2m 40 300 Nm 30 150 N 200 N Fig. 3

The L-shaped beam AB is resting on a smooth surface at A and supported by the collar at B which in turn is resting on a smooth rod built into the floor and wall supports as shown in Fig 3. Four loads and two moments of couples act on the beam as shown in Fig. 3. Calculate the reactions at the supports A and B. Neglect the thickness of the beam. 3. 250 N 500 N 30 3 m 4 m 4 m 3 m 40° 0.5m 250 Nm 2 m 2m 40 300 Nm 30 150 N 200 N Fig. 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(a) Assuming that no loads act in Figure P9.16,compute the reactions if support B is constructed 0.48 in.too low. Given: E = 29,000 kips/in.2, I = 300 in.4. (b) Ifsupport B settles _32 in. under the applied loads, computethe reactions.
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
a) The truss structure in Figure Q4 is supported at A and D with downward vertical load F1 acting at joint E and a downward vertical load F2 acting at joint C. The length of each truss member AB, BE, BC, CD and CF is 1.25 m. If F1 = 95 kN and F2 = 225 kN, determine the reaction force RA and RD at the supports A and D. Give your answers in kilonewtons (kN) to two decimal places. b) For the truss structure in Figure Q4, determine the forces FAE, FAB and FCF acting in members AE, AB & CF and clearly state if each member is in compression or in tension. Give your answers in kilonewtons (kN) to two decimal places. c) A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young’s Modulus, E, of 5.8 x 1011 N/m2, calculate: (i) the tie-rod’s extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (iii) the strain…
A beam shown below is supported by a strut DB and carrying a load P 60KN Determine the force acting m with strut and the reaction at point
Each of the three frame bars in the figure has a linear mass of 12 kg/m. Locate the position (?̅, ?̅) of the center of mass. Neglect the size of the pins and the thickness of the bars. Also calculate the reactions at the pinned fixed support at A and at the sliding support at E. What value would the reactions at A and E have if the bar BD were removed from the frame? Consider g = 9.81 m/s2
(a) Determine all reactions and bar forces pro-duced by the applied load in Figure P9.33. (b) If supportB settles 1 in. and support C settles 0.5 in. while the loadacts, recompute the reactions and bar forces. For all barsthe area = 2 in.2and E = 30,000 kips/in.2
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where M0 = 1,220 N-m, P = 2650 N, w0 = 1702 N/m, a = 2 m, b = 1.5 m, c = 3.5 m, d = 1.5 m
In the beam loaded as shown in the figure, 4. Find the reaction at the left support. a. 36 kN b. 25 kN c. 15 kN d. 35 kN 5. Find the absolute max shear a. 41 kN b. 71 kN c. 90 kN d. 105 kN 3. Find the location of maximum positive beam moment measured from point a. a. 4.437 m b. 5.437 m c. 1.732 m d. 2.273 m
Calculate the vertical reaction at support B. When sketching FBD, assume the positive direction of all reactions in the positive direction of y axis. Enter your answer in kN to two decimal places.
A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
In the beam loaded as shown in the figure, 1. Find the reaction at the left support. a. 36.25kN b. 46.25 kN c. -36.25kN d. -46.25kN 2. Find the absolute max shear a. 41.25 kN b. 71.25 kN c. 90kN d. 81.25 kN 3. Find the location of maximum positive beam moment measured from point a a. 4.4375m b. 5.4375m c. 7.4375m d. 6.4375m
If the 300-kg drum has a center of mass at point G, determine the horizontal and vertical components of force acting at pin A and the reactions on the smooth pads C and D. The grip at B on member DAB resists both horizontal and vertical components of force at the rim of the drum.