An aluminum column (0,= 200 MPa) has a length of 8 m. and is fixed at the top and pinned at the bottom. The column is braced in the weak direction at a point located 5 m from the bottom of the column. If the cross-sectional area has the dimensions shown and the factor of safety is 2.5, determine the maximum load that can be safely applied to the column. 310 mm 10 mm 10 mm 180 mm 10 mm

An aluminum column (0,= 200 MPa) has a length of 8 m. and is fixed at the top and pinned at the bottom. The column is braced in the weak direction at a point located 5 m from the bottom of the column. If the cross-sectional area has the dimensions shown and the factor of safety is 2.5, determine the maximum load that can be safely applied to the column. 310 mm 10 mm 10 mm 180 mm 10 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.12P: A fixed-pinned column is a W310 × 21 steel shape and is designed to carry an axial load of 125 kN....

See similar textbooks

Similar questions

A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2.0 and a yield strength of 860 MPa (125,000 psi) for the steel
The circular section steel bar bent in L shape is attached to a fixed wall at end A. A force P is applied to the rod in the vertical direction from the free end C. In what range is the safe diameter value of this ductile rod according to Von-Mises criterion? P=3kN, L1=3m, L2=2m, sak= 400MPa, tak= 200MPa, safety factor : n = 2 p = 3
A 20 mm thick flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the factor of safety based on compression between the bolt and flange. The yield point of the bolt is 450 MPa. A. 4.75 B. 3.75 C. 2.75 D. 5.75
A cylindrical pressure vessel has an inner diameter of 5 ft and a thickness of 3/4 in. The stress capacity of the pressure vessel is 25ksi. If a safety factor of 1.2 is required for the design, determine the maximum internal pressure (in psi) it can sustain. A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
An industrial machine requires a solid, round piston connecting rod 200 mm long, between pin ends that is subjected to a maximum compression force of 80,000 N. Using a factor of safety of 2.5, what diameter is required if aluminum is used with properties Sy = 496 MPa and E = 71 GPa.
To use deformation compatibility equations to calculate loads and deflections for statically indeterminate axially loaded columns. As shown, two composite columns of steel and concrete are used to support a rigid platform. The columns are cylindrical, with a steel bar encased in concrete. The outer diameter of each column is dc = 26 cm . The steel in the left column has a diameter of d1 = 13 cm . A load of P = 56 kN is applied with L1 = 1.8 m and L2 = 1.9 m . The height of the columns is h = 2.2 m . The moduli of elasticity for steel and concrete are Es = 200 GPa and Ec = 30 GPa , respectively.
Refer to the set of bars made of a material with a yield strength of 350 MPa, determine the minimum dimensions h1 and h2 required. Apply a safety factor FS = 1.5 without flux. Each bar is 12 mm thick
An aluminum [E = 10,000 ksi] control rod with a circular cross section must not stretch more than 0.22 in. when the tension in the rod is 2100 lb. If the diameter of the rod is 0.372 in., determine the maximum length of the rod.
A column consists of a 2.5 m long hollow tube with an outside diameter equal to 1.5 times that of the inside diameter. The column must carry an axial load of 40 KN without buckling. Use a factor of safety of 5 and calculate the dimensions of the tube if one end is fixed and the other end is free. Use the Euler formula and take ?=200 ???.
A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 23 kN without stretching more than 4 mm. 13.18 mm 28.25 mm 20.13 mm 25.90 mm 21.81 mm
Compute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)