Question
An arc welding operation on nickel performs a
groove weld. The cross-sectional area of the weld is 36.0 mm?. The
welding velocity is 3.5 mm/sec. The heat transfer factor is 0.75, and the
melting factor = 0.65. The melting temperature of nickel is 1447 °C.
Determine the rate of heat generation by the welding source to
accomplish this weld.
Expand
Transcribed Image Text

An arc welding operation on nickel performs a groove weld. The cross-sectional area of the weld is 36.0 mm?. The welding velocity is 3.5 mm/sec. The heat transfer factor is 0.75, and the melting factor = 0.65. The melting temperature of nickel is 1447 °C. Determine the rate of heat generation by the welding source to accomplish this weld.

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Manufacturing Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: 2- Can anyone solve this problem with all steps ? Thanks

A: Click to see the answer

Q: A mass weighing 20 lb stretches a spring 4in. The mass is attached to a viscous damper with damping ...

A: Given data: The weight of the mass is w = 20 lb. The stretch in spring is L = 4 in. The damping con...

Q: Consider a tank of rectangular cross-section partially filled with a liquid placed on an inclined su...

A: The free body diagram of the tank is given below,

Q: Chain AB is 1 m long and chain AC is 1.2 m long. If the distance BC is 1.5 m, and AB can support a m...

A: Given Data: The maximum force in AB is F = 2 kN. The maximum force in AC is F' = 0.8 kN.

Q: *81. GO An irreversible engine operates between temperatures of 852 and 314 K. It absorbs 1285 J of ...

A: Given data: The temperature of the source is; T1=852 K. The temperature of the sink is; T2=314 K. T...

Q: P14-1. Determine the work of the force when it displaces 2 m. k = 10 N/m 2 m 500 N Spring is origina...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for...

Q: State the critical difference in the processing behavior of thermoplastics vs. thermosets.

A:           The primary physical difference is that thermoplastics can be remelted back into a liquid,...

Q: In Fig. , a cable is attached to the structure at E, passes around the 2-ft-diameter, frictionless p...

A: Draw the free body diagram for the complete problem. Now determine the moment about point G  and eq...

Q: Calculate how many billion years it will take to build 1 mole of a molecule with a formula of CnH2n+...

A: Click to see the answer

Q: A 20 °C water jet strikes a vane mounted on a tank withfrictionless wheels, as in Fig. P3.61. The je...

A: Given data: The velocity of jet, VJ = 50 ft/s. The diameter of jet, DJ = 2 in. The deflected angle,...

Q: Activity 2. What weight W is necessary to start the system of blocks shown to the right? The coeffic...

A: Click to see the answer

Q: Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m...

A: Given: The sea-level density is ρ=1.23 kg/m3. The lift on a circular cylinder is L=6 N/m. The veloci...

Q: Determine the tension in cables BA and BC necessary to support the 75-kg cylinder in the figure belo...

A: Click to see the answer

Q: Define incompressible flow and incompressible fluid. Must the flow of a compressible fluid necessari...

A: Incompressible flow refers to any fluid(liquid or gas)  flow where density of any fluid element rema...

Q: A centrifugal pump impeller delivers 4000 gal/min ofwater at 20 ° C with a shaft rotation rate of 17...

A: Given, Temperature (T) = 20 °C Q = 4000 gal/min  N = 1750 rpm r1 = 6 in r2 = 14 in b1 = b2 = 1.75 in...

Q: Q3 ASAP with a correct theory  SUBJECT - CAD

A: 3. CAD is a designing process which is used in modern designing practice. Computer raised design is ...

Q: Compared to drinking through a straw on earth, would it be easier or more difficult to drink a liqui...

A: Acceleration due to gravity is the acceleration of a free falling body when it is allowed to be attr...

Q: Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is open to the atmosphe...

A: Density of water = 1000 kg/m3 Height of tank H = 80 m η = 0.75 motor power = 3.2 kW m ˙ =16560= 2.75...

Q: The 180-N force is applied to the end of body OAB. If 50, determine the equivalent force-couple syst...

A: Click to see the answer

Q: The portion of a bridge truss is subjected to several loads. For the loading shown, determine the lo...

A: Draw the free body diagram of the given truss.

Q: Is the Eulerian method of fluid flow analysis more similar to study of a system or a control volume?...

A: The description or analysis of fluid flow is basic learning in the study of hydraulics and fluid mec...

Q: 5.1 Determine the spring constant of the spring arrangement if all springs have the same spring cons...

A: Click to see the answer

Q: a.) What is the angle, measured relative to the positive x-axis, of the load's acceleration? (The co...

A: Click to see the answer

Q: When does stress concentration occur?

A: The region or location in a material/0bject where the stress is concentrated more compared to other ...

Q: 18-49. The assembly consists of two 10-kg bars which are pin connected. If the bars are released fro...

A: Given: mass of the rod -10kg mass of the disk = 5kg disk rolls without slipping  to find the angula...

Q: Fill in the truth tables and write the corresponding Boolean logic statement.

A: The Exclusive-OR gate use to comparison between two logic levels and generates an output value depen...

Q: The compound arrangement of the pan scale is shown. Part A: If the mass on the pan scale is 4 kg, de...

A: Click to see the answer

Q: FAB Find the Projected Force to direction AC in N. (Hint: Dot Product).

A: The unit vector of AB and AC is as follows: UAB=-2-0i^+0-3j^+1-0k^-2-02+0-32+1-02UAB=-2i^-3j^+1k^14 ...

Q: The thrust F of a propeller is generally thought to be afunction of its diameter D and angular veloc...

A: The thrust force is the function of F=fD,ω,V,μ,ρ here n=6m=3 Now the replacing variables are μ,V,D T...

Q: In order to produce a certain semiconductor, a process called doping is performed in which phosphoru...

A: Click to see the answer

Q: 10-65. The shaft is made of 12 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B...

A: Given, L1 = 800 mm = 0.8 m L2 = 600 mm = 0.6 m D = 40 mm = 0.04 m r = d/2 = 0.04/2 = 0.02 m Torque ...

Q: A rigid tank contains 20 lbm of air at 20 psia and 70°F. More air is added to the tank until the pre...

A: Given: The initial mass of the air is m1=20 lbm. The initial pressure of the air is P1=20 psia. The ...

Q: Determine the magnitude of the resultant force in 0 = 31 degrees and T = 5 KN. Provide the answer in...

A: Click to see the answer

Q: 16-98. If the hub gear H has an angular velocity wn = 5 rad/s, determine the angular velocity of the...

A: Given: The angular velocity of hub gear H = 5 rad/s The spur gear is stationary.

Q: d) Pressure head at point 1 e) Pressure head at point 2

A: Click to see the answer

Q: Each stage of an axial flow compressor is of 0.5 reaction, has the same mean blade speed and the sam...

A: Given data: At entry to first stage: Stagnation conditions: P01=101.3 kPa, T01=278 kPa, Static press...

Q: An acrobat is walking on a tightrope of length L-20.1 m attached to supports A and B at a distance o...

A: Given, Length of the rope is 20.1 m Distance between AB is 20 m Let, Length of lope AC=l Horizontal ...

Q: A 39-ft length of railroad rail of weight 44 lb/ft is lifted by the tongs shown. Determine the force...

A: Given Length of rail road = 39 ft Weight 44lb/ft is lifted by the tings To find Force exerted at D a...

Q: The following engineering tensile properties are given for the 1080 steel:-Yield strength (MPa): 585...

A: Part a As we know the tensile stress is given as σ=FAhere we haveσ=965 MPaA=π4D2here D=1.28x10...giv...