An architetect wants to design a semicircular tunnel so that two average trucks measuring 9 feet wide and 11 feet tall can pass each other with a 3 feet clearance between them (w), and 3 feet clearance with the ceiling (z). Round your answers to two decimal places. 1. What is the smallest posible center height of the tunnel? ______ feet Answer: 2 What is the height of the tallest 10 feet wide vehicle that can drive down the center of the tunnel maintaining the minimum vertical clearance of 3 feet? Answer ______ feet

An architetect wants to design a semicircular tunnel so that two average trucks measuring 9 feet wide and 11 feet tall can pass each other with a 3 feet clearance between them (w), and 3 feet clearance with the ceiling (z). Round your answers to two decimal places. 1. What is the smallest posible center height of the tunnel? feet Answer: 2 What is the height of the tallest 10 feet wide vehicle that can drive down the center of the tunnel maintaining the minimum vertical clearance of 3 feet? Answer feet

Name: An architetect wants to design a semicircular tunnel so that two avera
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: An architetect wants to design a semicircular tunnel so that two average trucks measuring 9 feetwide and 11 feet tall can pass each other with a 3 feet clearance between them (w), and 3 feetclearance with the ceiling (z).Round your answers to two dec

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 14RQ: A plane used as a reference for dimensions is called a(n) __________ __________.

See similar textbooks

Similar questions

Asap please… 3 Decimals.. Use g=9.81 m/s2, g=32.2 ft/s2. No rounding off in the solutions. Thank youuu
There are 26 heavy smokers in a lounge. The minimum fresh air requirement for smoking lounges by ASHRAE is 30L/s per person. Solve for the minimum diameter in m of the duct if the air velocity is not to exceed 7.88m/s. Round your answer to 3 decimal places.
A plane used as a reference for dimensions is called a(n) __________ __________.
The elevations of the ski jumping hill shown below are as follows: hA = 37 mhB = 2.4 mhC = 5.5 m If the velocity of a ski jumper is measured to be 25.3 m/s at position B, what will be the launch velocity (in m/s) at position C [round your final answer to one decimal place]?
ques 6 part a plz answer asap
A flue from an oil furnace to the chimney is made from 9 pieces of pipe. Afterbeing fitted together, each piece of pipe is 1 foot 101⁄2 inches long. What isthe total length of the flue?
find the diameter of cylinder, specific weight is=25 N/m^3, Mass=2.2lbs, Acceleration=32.2m/s^2, height is 1meter. final answer should be in inches
How are you getting 16 mm at the end for an answer , "HX83=219X10^3/164.909".................is that your diving by f/a and multiplying by 83 to get H , im just no sure what you did to get 16 ?.
The most powerful engine available for the classic 1963Chevrolet Corvette Sting Ray developed 360 horsepower and had a displacement of 327 cubic inches. Express this displacement in liters (L) by using only the conversions 1 L = 1000 cm3 and1 in. = 2.54 cm.
Ptip is 46.97, but Mobius says the answer of 30.52 is incorrect for Pslip
two cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m
I got -133.344Kn but that was incorrect. Need help and the answer has to be to three decimal points.