'D' dimension : Basic size Tolerance Max size Min size . 'E' dimension : Max size Min size

Q: The .. slope indicates a constant acceleration. *

A: ZERO SLOPE

Q: 9/16 inch is approximately equivalent to . mm. 19 17 14 12

A: The dial indicator is a traditional mechanical kind with a dial display that resembles a clock face…

Q: -bide and ste exponent of 0.

A:

Q: The following limits are specified in a limit system, to give a clearance fit between a hole and a…

A:

Q: Compute the following: Basic size Tolerance Maximum limit size Minimum limit size

A: Machine drawing is the drawing in which component details are given in geometrical view. For…

Q: n outside diameter of 70 m and :

A: here outer dia (70m) is >>>> inner dia (50mm). so the polar moment of inertia almost…

Q: The given system Measured values has True value accuracy.

A: Let us discuss about accuracy from given figure.

Q: Determine the correctness

A: Given; Assertion A:       In a power plant working on a Rankine cycle, the regenerative   feed water…

Q: In thread cutting operation, pitch of thread is defined as а. Depth of thread b. Difference outer…

A: The distance between the two points starting from the one point on one thread to the…

Q: Select the correct statement to represent the above problem (Answers are more than one).

A: (J) Correct explanation- The us = 0.3 is the coefficient of static friction that can be…

Q: 12) Mention two instruments used to measure internal linear dimensions.

A: Q12) Mention two instruments used to measure internal linear dimensions.,

Q: Imdia water Mercary 0.25m

A:

Q: A

A: Given : The tolerance off hole = 0.5

Q: 50. Tolerance (a) About how accurately must the interior diameter of a 10-m high cylindrical storage…

A: Given Data Interior diameter is : d=10 m (a) Consider the interior diameter of a 10m high…

Q: min. Cylinder wall thickness for safe design

A: Given; Thin cylinder with an internal radius=100 mmor, d=2r           =100×2           =200…

Q: 3x – 2

A:

Q: Plzz solve I give you rating

A: Given unidirectional laminate, vf=Fibre volume fraction=0.55Ef=Young's modulus of carbon fire=310…

Q: 600 mm C 360mm

A:

Q: Which type of feature doesn't belong to form tolerances? Circularity The profile of a surface…

A: As we know principle component of form tolerence are Straightness.Flatness.Roundness.Cylindricity.

Q: All form tolerances are surface controls except for Form tolerances are independent of all other and

A: Form tolerance is a used to determine the form of the part. It refers to the limitation of a form…

Q: determine the minimum preferred size diameter.

A: Given: FOS=3  T2=0.15T2 To determine: The minimum diameter using distortion energy theory

Q: The dimensions of the mating parts, according to basic hole system, are given as follows: Hole :…

A: Given, Upper limit of hole = Hu = 25.02 mm Lower limit of hole = Hl = 25.00 mm Upper limit of shaft…

Q: Given data: Stain=0.00021 Initial length=120 mm Find change in length

A: Given data : Strain=ε Initial length=L   Required : Change in length

Q: EH, FG, EG and GH. 10KN 4m 3m 3m 20 kN 3m 3m 30KN 3m 3m

A:

Q: find the diameter of cylinder, specific weight is=25 N/m^3, Mass=2.2lbs, Acceleration=32.2m/s^2,…

A: Given :-  Specific weight = 25 N/m2 Mass (m) = 2.2 lb = 0.997903 kg Height of the cylinder (h) = 1 m…

Q: 8) __________ notched specimens are used for Charpy impact test. Select one: V U & V U Key hole

A: V notched specimens are used for charpy impact test

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: The value of RSS (in mm),

A: Given;  Solid steel disc of initial radius, → RIN=200 mm→ Initial height, HIN=50mm→Attains a height…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Which method specifies the tolerance by providing dimensions for the upper and lower limit in place…

A: Definition of Tolerance : Tolerance is the total permissible variation of a size, means it is not…

Q: For an ordinary concrete slab to be laid" -3 within tolerance, engineers can only realistically…

A: Given question is related to metrology and inspection We have to complete the expression that is…

Q: Which option is wrong?       A bilateral tolerance allows a dimension to vary both above and below…

A: Concept Of Metrology Used

Q: Comect AniSwer 20 Coarse Nominal diameter Coarse or fine pitch Pitch

A: Solution   The nominal diameter is the distance across from peak to peak that the fastener is listed…

Q: the minimum metric

A: Given; For the three bolt system shown in the figure,shear yield strength=200 MPaFOS=2The min.…

Q: Compute the degree of freedom.

A: Number of links in the mechanism= 10 Number of joints in the mechanism= 12 Number of higher pairs in…

Q: maximum eccentricity of the bush in mm will

A: Given;A brush was turned after mounting the same on a mandrel.The mandrel diameter=40-0.05+0.00…

Q: Determine time required/pass

A: Given; In a surface broaching process,   Broach pitch=6 mmand    Cut per teeth= 0.05 mmIt is used…

Q: state the functions of interference fit and draw it on illustration of size tolerance zone .

A:

Q: is 10 min short- dia 3 mm. Finds es hy o'mpress by 20

A:

Q: e allowable position tolerance that may be applied to each part in a

A: Determine The applied allowable position tolerance

Q: a nominal size of 50 mm are as follows: Hole

A:

Q: speed.

A: Given; A milling cutter having teeth is rotating at;  N= 135 rpmIf the tooth is, f=0.1 mmDetermine…

Q: The appropriate diameter is mm.

A: To find  diameter

Q: In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70…

A: Given: Dimensions of,Hole=70+0.00+0.04mmShaft=70-0.08-0.04mm

Q: Several of the problems are not dimensioned. Use 5mm grid spacing and 10mm spacing between views.…

A: Please refer the following image for the required views as per the requirement.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.