An austenite containing 0.55% C was slowly cooled below 727°C, what would be its resulting microstructure? Composition (at% C) 10 15 20 25 1600 1538°C -1493 C L 1400 2500 1394°C 7+L 1200 1147°C 2.14 4.30 Y, Austenite 2000 1000 912°C y+ FezC 800 1500 727°C 0.76 0.022 600 `a, Ferrite a+ FegC Cementite (Fe;C). 1000 400 1 2 3 6.70 (Fe) Composition (wt% C) Temperature ("C) Temperature (F)

An austenite containing 0.55% C was slowly cooled below 727°C, what would be its resulting microstructure? Composition (at% C) 10 15 20 25 1600 1538°C -1493 C L 1400 2500 1394°C 7+L 1200 1147°C 2.14 4.30 Y, Austenite 2000 1000 912°C y+ FezC 800 1500 727°C 0.76 0.022 600 `a, Ferrite a+ FegC Cementite (Fe;C). 1000 400 1 2 3 6.70 (Fe) Composition (wt% C) Temperature ("C) Temperature (F)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the amounts and compositions of phases at 726oC in a Fe-0.6% C alloy cooled under equilibrium conditions. Disregard the amounts of proeutectoid phases. A. 77.3% α, 22.7% Fe3C; C in α = 6.7% and C in Fe3C = 0.02% B. 91.3% α, 8.7% Fe3C; C in α = 0.02% and C in Fe3C = 6.7% C. 77.3% α, 22.7% Fe3C; C in α = 0.02% and C in Fe3C = 6.7% D. 91.3% α, 8.7% Fe3C; C in α = 0.05% and C in Fe3C = 8.4% E. None of the mentioned
For a 50-50 Mg-Pb alloy, what would the percent of each phase be at 500°C, 300°C and 100°C?
10.15) A magnesium-lead alloy of mass 5.5 ka consists of a solid a phase that has a compo- sition that is just slightly below the solubility limit at 200°C (390°F). (a) What mass of lead is in the alloy? (b) If the alloy is heated to 350°C (660°F). how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase?
For a 70-30 Zn-Cu alloy, what would the percent of each phase be at 800°C and 500°C?
(11.10) Suppose that a steel of eutectoid composi- tion is cooled to 550°C (1020°F) from 760°C(1400°F) in less than 0.5 s and held at this temperature. (a) How long will it take for the austenite- to pearlite reaction to go to 50% comple- ton? To 100% completion? (b) Estimate the hardness of the alloy that has completely transformed to pearlite? 11.12) Briefly cite the differences between pearl- rp. bainite, and spheroidite relative to crostructure and mechanical properties?
Suppose you wanted to have two samples of NiTi wire: one that is in the high-temperature austenite phase at 0°C, and one that is in the low-temperature martensite phase at 0°C. Which of the compositions of NiTi below would you choose for which sample? Composition A: 50% Ni, 50% Ti Composition B: 52% Ni, 48% Ti
Draw the iron-Fe3C phase diagram. Consider 0.4 and 1.1 wt% C steel alloy. It is cooled slowly from a temperature within austenite phase to room temperature. Show a) microstructure at 1000 °C b) microstructure at 730°C c) microstructure at 715°C and d) microstructure at room temperature e) determine the phase present, the phase compositions at 715 and 730 °C f) What do you say about mechanical properties of these alloys, depending on their microstructure at room temperature?
For a 60-40 Pb-Sn alloy, what would the percent of each phase be at 185°C and 180°C?
Use the copper silver phase diagram below. 100g of a 40 wt% Cu 60 wt% Ag alloy is made and cooled from liquid form. a. At what temperature does the solid phase start to appear? b. What phases exist at 780°C? c. What are the compositions (Cu and Ag%) of the phases in question b? d. What are the weights (in g) of Cu in the solid phase and liquid phase in question b?
An alloy of 30 wt % Pb and 70 wt % Sn is slowly cooled from 250°C to 27°C: a) Is this alloy hypoeutectic or hypereutectic? b) What is the composition of the first solid to form? c) What are the amounts and compositions of each phase that is present at 183°C + ∆T ? d) What is the amount and composition of each phase that is present at 183°C - ∆T ? e) What are the amounts of each phase present at room temperature? f) Draw the microstructure 183°C + ∆T and 183°C - ∆T in 2 cm diameter circle.
What is the chemical composition upper limit of carbon for steel?A) 5%B) 0.022%C) 2.11%D) 4.3%E) 0.8% 2- Is it in liquid or semi-liquid state consisting of data and solidifies in a vacuum?A) tattooB) machiningC) pre-cookingD) castingE) turning 4- Which element has the lowest density and lowest atomic weight?A) magnesiumB) hydrogenC) heliumD) aluminumE) argon
An alloy of 30 wt % Pb and 70 wt % Sn is slowly cooled from 250°C to 27°C: d) What is the amount and composition of each phase that is present at 183°C - ∆T ? e) What are the amounts of each phase present at room temperature? f) Draw the microstructure 183°C + ∆T and 183°C - ∆T in 2 cm diameter circle.