An electrical po With a Vrms, 50 H2 ighting, COORING anu entertainment. If specification of the loads is 300 W with 400 VA lagging, 200 W with 0.88 power factor leading and 150 VAR with 0.77 power lagging respectively, solve this completed power system by calculating the following parameters: a) supply current, Is b) total of load impedance, ZT (load)

An electrical po With a Vrms, 50 H2 ighting, COORING anu entertainment. If specification of the loads is 300 W with 400 VA lagging, 200 W with 0.88 power factor leading and 150 VAR with 0.77 power lagging respectively, solve this completed power system by calculating the following parameters: a) supply current, Is b) total of load impedance, ZT (load)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
Given a 400sq.m single family dwelling unit to be provided with 230V, 1-phase, 2-wire be service, andhaving the following loads: 2-1.5hp A/C, 2-1.0hp A/C, 1-0.5hp water pump, 4-800W water heater, 2-6kWelectric range and 2-1kW microwave oven, determine a) the total connected load, b) the total demand load,c) the overall %demand factor, d) the size of THW feeder conductor, ground wire and IMC conduit, e) therating of feeder overcurrent protection using inverse time circuit breaker
If the values of real power and reactive power is specified for a bus, then it is called as PQ bus. Select one: True False
The area of an interconnected power system has two units operating on economic dispatch. The variable operating costs of these units are given by C =8P +0.009P2 11 1(R/h) and C = 10P + 0.008P2 where P1 and P2 are in MW. The transmission losses for the area are given by ? = 1.5 × 10−4?2 + 2 × 10−5? ? + 3 × 10−5?2 , MW ?1122 2 2 2 (R/h,) Determine the following when the area λ = 16.00 R/MWh: a. The output of each unit b. Total transmission losses c. Total load demand d. Total operating cost
In the network, find the value of ZL for maximum power transfer. The load impedance has both variable resistance and variable reactance. In addition, calculate the maximum power dissipated under these conditions, PS: Show complete/step-by-step solution without rounding off any numbers.
What is a smart grid, and how does it improve the reliability and efficiency of power systems? Provide real-world examples of smart grid implementations.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
A 3-phase, 50 Hz overhead transmission line, 100 km long, 110 kV between the lines at the receiving end has the following constants : Resistance per km per phase = 0·153 W Inductance per km per phase = 1·21 mH Capacitance per km per phase = 0·00958 µF The line supplies a load of 20,000 kW at 0·9 power factor lagging. Calculate using nominal p representation, the sending end voltage, current, power factor, regulation, and the efficiency of the line. Neglect leakage.
Analyze the impact of distributed energy resources (DERs) and smart grid technologies on the modernization of power systems.
Exercise 1: A three-phase 3Φ transmission line has an impedance of 0.62+j35.06Ω/phase and supplies a three-phase load of 100MW with a power factor (fp) of 0.8 lagging at 200kV. Taking 100MVA and 215kV as a base, we ask: d-) Calculate the complex power consumed by the load in p.u;e-) Calculate the voltage at the emitter terminal in p.u;f-) Calculate the LT impedance taking 200MVA and 150kV as a new base. PLEASE, TYPE, HAND WRITING GETS UNDERSTANDING.
2) The net inlet to a factory powered by a 2300 volt infinite busis measured as 765 A, for a lag 0.92 power factor. although mostloads is inductive, the input power factor has been improved by installing asynchronous capacitor operating at its nominal value of 1000 KVA. Determine the factor oforiginal factory power.