1. A certain full-wave rectifier has a peak output voltage of 30 V. A 50 μF capacitor-input filter is connected to the rectifier. a. Calculate the peak-to-peak ripple and the dc output voltage developed across a 600Ω load resistance. b. Determine the percentage of ripple for the rectifier filter. Please show me all the calculations steps so that I can understand well and thank you for your time

1. A certain full-wave rectifier has a peak output voltage of 30 V. A 50 μF capacitor-input filter is connected to the rectifier. a. Calculate the peak-to-peak ripple and the dc output voltage developed across a 600Ω load resistance. b. Determine the percentage of ripple for the rectifier filter. Please show me all the calculations steps so that I can understand well and thank you for your time

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 3PA: An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
Design a full wave rectifier with capacitor filter, using a centrally tapped Trafo to supply a load of 100Ω. Specify all components: Trafo, rectifier diodes, capacitor filter and power dissipated in the load. The ripple should not exceed 3.0Vpp. THE load voltage should be 30 VDC. (0.5) Draw the electrical circuit of the rectifier correctly. Watch out for the units!
single phase half wave controlled rectifier has a source of 220V, f = 50Hz is feeding a R = 15Omega load The a=30 1- sketch the input and output voltage 2- derive the output voltage and compute it 3- find the ripple factor 4- power factor 5-PIV
1) A certain full-wave rectifier has a peak output voltage of 30 V. A 50 μF capacitor-input filter is connected to the rectifier. a. Calculate the peak-to-peak ripple and the dc output voltage developed across a 600Ω load resistance. b. Determine the percentage of ripple for the rectifier filter.
Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
The gate current of an SCR full-wave rectifier is adjusted to 1.2mA and the forward breakdown voltage of SCR corresponding to this gate current is 150V. The applied voltage is a sinusoidal voltage of 300V peak, the load resistance is 100 ohms and the holding current is zero. Determine the a) firing angle b) conduction angle c) average output voltage d) average current and e) average power (Our lesson is POWER ELECTRONIC DEVICES, in the lesson of INDUSTRIAL ELECTRONIC)
Assume AT the output of a filtered half wave rectifier circuit a series resistor RS of 4.2kohm together with a shunt connected 54v zener diode is now connected as a simple regulated circuit. The zener is connected in parallel with load RL of 11.9 kohm. When the input mains voltage flutes at various parts of day the max DC voltage appearing across the capacitor is 120 V and thefor the above zener maximum voltage is 80 V. Determine the load current in mA flowing through the load,
When comparing the efficiency of full-wave and half-wave rectifiers, one of the following statements is correct: Select one: a. Full-wave rectifier has a twice the efficiency of a hlaf-wave rectifier because it utilizes both half cycles of the input b. Full-wave rectifier has a twice the efficiency of a hlaf-wave rectifier because it makes use of a transformer c. Half-wave rectifier has half of the efficiency of a full-wave rectifier because the output frequency is double the line frequency d. Half-wave rectifier has half of the efficiency of a full-wave rectifier because it uses less number of diodes e. Half-wave rectifier has half of the efficiency of a full-wave rectifier because the ripple factor is much less
A half-wave rectifier with a reservoir capacitor is connected to an AC mains supply(220Vrms, 50Hz) via a 20:1 transformer. What value of the capacitor is needed forthe ripple voltage of X% of the peak input voltage? The load takes a maximum currentof ???? mA. X= 12% mA = 160
A full-wave rectifier circuit is shown. Assume that the input voltage vp = 220 Vrms of 60 Hz AC supply. The rectifier diodes cut-in voltage, Vγ = 0.7 V and rf = 0 Ω. The output peak current of the circuit, io(peak) = 2 mA when the peak output voltage, vo(peak) = 11.75 V. i. Determine the required turns ratio of the transformer. ii. Assume that a capacitor is added in parallel to the resistor RL to limit the ripple voltage, Vr = 0.25 V. Determine the value of the capacitor.
Choose the correct answer 1. Increasing the value of a resistor in an RC circuit at the output of a rectifier will result in a)Smooth DC output b)Distorted DC output c)Output will not be a pure DC d)No effect 2. Connecting a capacitor at the output of a rectifier will serve as a a) Filter b)Charge storage device c)Bypass capacitor d)None of the above 3. In a half-wave rectifier, peak value of the output waveform is always a) Equal to the input wave b) Higher than the input wave c) Less than the input wave d) It depends upon the diodes 4. RMS value calculation involves which of the following steps a) Square root of all values, taking mean, and then squaring b) Squaring all the values, taking mean, and then square root c) Squaring all the values, square root them, and then taking mean d) None of the above 5. In a full-wave rectifier, peak…