An emitter follower output stage has Vcc = 10 V,R3 =5 k2, VCEsat= 0.2 V, RL = 1 kQ. Assume thesignals are sinusoidal.+VecA) select R1 and R2 to make the efficiency 10%Hint: IQ must be more than IRB) If R1=R2=0. select R3 to make RL follow thesituation of RL1. calculate the corresponding loadpower , efficiency, and the maximum instantaneouspower dissipation in Q1-Vec21

Given: An emitter follower output stage has: VCC=10 VR3=5 kΩVCEsat=0.2 VRL=1 kΩ Assume signals are…

Answered: An emitter follower output stage has…

An emitter follower output stage has Vcc = 10 V, R3 =5 kQ, VCEsat= 0.2 V, RL = 1 k2. Assume the signals are sinusoidal. A) select R1 and R2 to make the efficiency 10%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: In a transistor circuit, collector load is 4 kΩ whereas quiescent current (zero signal collector…

A: Given, Collector load, Rc = 4 kohm Quiescent current (IcQ)= 1 mA

Q: 1.) IS THE POSSIBLE SWING MA XIMI ZED? a-) YES. THE SELECTED VALUE OF Vour IS EXACTLY HAF of THE…

A: The given circuit is as shown below, We need to justify whether the possible swing is maximized or…

Q: Draw the equivalent circuit model and switching characteristics of the MOSFET

Q: 1. Draw the re model for both bypassed and un-bypassed common emitter bias configuration (ВJT).

Q: A Sketch a transistor-level schematic of F = A’B’(A’E’ + C')(D' +E') and determine the relative…

A: Given: The function: F=A'B'A'E'+C'D'+E' To find: Sketch a transistor-level schematic and determine…

Q: Consider circuit with VDD = Vss = 5 V, RG = 10 MQ, RD = Rs = 3 kN, switch is open. The input sine…

A: Given Data: Vdd = Vss = 5 V Rg = 10 Mohm Rd = Rs = 3 kohm

Q: 1.a) Calculate Ay, A¡, Rin, and Rout on the circuit given in Figure 1. Assume that Cci and Cco…

A: consider the given question.

Q: Summary Comparison of BJT, JFET and MOSFET Solid State Devices Disadvantages When Invented…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Consider the emitter follower in Figure 1 with Vcc= 10?, I = 100 mA, and RL = 100ohm. (a) Find the…

A: (a) Under quiescent condition Vo= 0 V and each Q1 and Q2 conducts carrying current I=100 mA I==…

Q: A) What does VCO stand four? Show by drawing the relationship between its input and output signals.…

A: VCO stands for Voltage-Controlled Oscillator This is an oscillator whose output frequency is…

Q: Suppose -Vcc is connected to the ground, What happens to the LED when Vin< Vref and how? What is…

A: According to the question, for the circuit shown below Suppose -Vcc is connected to the ground,…

Q: 20V Rc 3k Rb 430k VCE

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: XProblem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (Vcc) at…

A: First we will find out the Current then we will find out voltage

Q: Assuming B = 100, Calcu;late Ic, Ve, Vc and Vce in figure below? +15 V 10 k 15 k. 12 k -25 V…

Q: Q2)NPN Si transistor in common emitter mode has been biased using voltage divider bias method. Let…

A: Note: As per our policy, I have attem[ted the first three subquestions. Given data: Vcc=12…

Q: Consider class-A emitter follower circuit shown in the figure below. The circuit parameters are V+ =…

A: The parameters of a Class-A emitter follower circuit are as follows,V+ =…

Q: Draw the equivalent circuit model and switching characteristics of the device which is having high…

A: A power diode has a P-I-N structure as compared to the signal diode having a P-N structure. Here, I…

Q: Q2 EMI is a very important aspect to be considered while designing a switching power supply. Discuss…

A: EMI refers to Electro Magnetic Induction , which briefly means in terms of PCB designing, the…

Q: For the circuit shown in Figure B19a, Ve 20V Rc 3kQ RB = 10k 2 VCE VBB=3V Figure B19a i) Sketch the…

Q: xProblem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (vcc) at…

A: We need to find out collector terminal voltage for given details .

Q: VDD VDD VDD IREF Ιουτ M3 M4 M1 M2 Figure 1

Q: Q 1. Derive the Avr, Rit, Rof, R'ofr for the circuit shown in figure 1. For each transistor the…

Q: Consider Figure 8 below and assume that for a pnp transistor the emitter and base currents are IE =…

Q: i. Design a current source such that IR = 10 mA and Io1 = 15 mA and Io2 = 25 µA by assuming MOSFET…

Q: 10.14 For the circuit shown in Figure P10.14, determine the base voltage Vg required to saturate the…

A: Redrawing the given circuit:

Q: XProblem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (Vcc) at…

Q: Explain the working principle of a metal oxide field effect transistor (MOSFET).

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Ideally, for linear operation, a transistor should be biased so that the Q-point is halfway between…

Q: 6.13 POST LAB QUESTIONS 1. Define current gain in CE configuration? 2. Why CE configuration is…

A: (i) The current gain is defined as ration of output current to the input current In CE configuration…

Q: 1. What is the meaning of common emitter configuration? 2. In the common emitter configuration, what…

A: Here as per the honor code we are supposed to answer only the 1st question. Hence upload the other…

Q: Subject:Electronics Engineering How MOSFET has been constructed? Explain the principle of operation…

A: Metal Oxide Silicon Field Effect Transistors: MOSFETs is a electronic devices, that is used in…

Q: 40k2 10KR 10UF Vout 10uF Vin

A: For calculation of parameters asked in the question we have to perform DC analysis in which the…

Q: For the given circuit, Vcc = 18 volts, RB = 500 KN, RC = 9 KN and B = 180. Assume Transistor is…

A: A good question on analog transistor biasing.

Q: What is the voltage value Vgs for the n-channel MOSFET given in the figure? (VT=2V, K=0.4mA/V^2,…

Q: Ic 3302 RC IB Vcc 20V 47 k2 VBE VBB 10V IE

A: We need to find out the current and voltage for given circuit .

Q: draw a qpsk modulator circuit using different circuit compents like resistors, transistors etc not a…

A: qpsk : Quadrature Phase Shift Keying is form of Phase Shift Keying in which two bits are modulated…

Q: For the class B output stage of Figure 2, let ??? = 6 V and ?? = 4Ω. If the output is a sinusoidal…

A: Given, Vcc=6VRL=4 ΩVpeak=4.5 VVrms=4.52=3.18 V ,

Q: Question 1: For the Mosfet in the circuit shown below: ID = ImA, VTP = - 0.586V, RGI = 2M, and…

Q: 1.a) Calculate Ay, A¡, Rin, and Rout on the circuit given in Figure 1. Assume that Cci and Cco…

A: consider the given question;

Q: Consider an n-channel metal-oxide-semiconductor field-effect transistor (MOSFET) with a…

A: Given- MOSFET- Ratio of width of the gate and channel length- WL=4, Mobility of the carrier × Oxide…

Q: 2021H (a) Plot the output characteristics of the transistor (b) Draw the DC load line (c) Determine…

Q: This is a plot of IC vs VCE characteristics of NPN Transistor. Redraw and shade the different…

A: BJT is a current controlled Device in which base current control the mode of operation of BJT…

Q: For each transistor shown in Figure P10.1,determine whether the BE and BC junctions areforward- or…

A: (a) Given transistor is – From figure – It is a pnp transistor. Value of voltage VBE = -0.6V and…

Q: Figure shows a CE power amplifier in which the collector resistor serves also as the load esistor.…

Q: Rc 50 ohm Vcc = 10V Vg= 0.8 V - Calculate the lc for Q1. Show that Q1 is in Forward Active…

A: NOTE: Since you have posted multiple independent questions in the same request, We will solve the…

Q: |12.5 The class A emitter follower in the figure to the right is to operate from +/- 10 V supplies…

A: The problem can be solved in the following way: Let the current gain of the transistor is infinite.…

Q: Draw the equivalent circuit model and switching characteristics of the device which is having high…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: (a). (b). Describe the cut-off mode of a transistor. An amplifier circuit with a bipolar junction…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Determine how much the Q-point (Ic, VCe) for the circuit in Figure given below will change if Bpc…

Concept explainers

Power Amplifier

The power amplifier is an electronic amplifier designed to maximize the signal strength of a given input. The input signal strength is enhanced to a high enough level to drive output devices such as speakers, headphones, RF (Radio frequency) transmitters, etc. Unlike voltage / current amplifiers, the power amplifier is designed to drive core loads directly and is used as a storage block in the amplifier series.

Maximum Efficiency Criterion

In every field of engineering, there is a tremendous use of the machine and all those machines are equipped for their popular work efficiency so it very much important for operation engineers to monitor the efficiency of the machine, planning engineers to check out the efficiency of the machine before installing the machine and design engineers to design machine for higher efficiency than and then the utility will procure their products that will ultimately lead to profit and loss of the company. It indicates the importance of efficiency right from the initial stage as manufacturing units, intermediate stage as planning coordinators, and end-users stage as a utility.

Question

An emitter follower output stage has Vcc = 10 V,
R3 =5 k2, VCEsat= 0.2 V, RL = 1 kQ. Assume the
signals are sinusoidal.
+Vec
A) select R1 and R2 to make the efficiency 10%
Hint: IQ must be more than IR
B) If R1=R2=0. select R3 to make RL follow the
situation of RL1. calculate the corresponding load
power , efficiency, and the maximum instantaneous
power dissipation in Q1
-Vec
21

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the circuit in the figure, VGSQ = 6.8 V, IDQ = 2.4 mA, VGS(Th) = 3.3 V, k = 0.4x10-3 A/V2, RD = 5.6 kΩ, RF = 2.2 MΩ and rd = 25 kΩ. Accordingly, when a RL = 23.6 kΩ load is connected to the output of the circuit, what will be the voltage gain of the circuit? NOTE: MOSFET output resistance must be taken into account in rd calculations.
Design a Single-Stage Common Emitter Class A Amplifier Specifications:Voltage Divider Bias Circuit Supply: Any value from 10Vdc to 24VdcLoad: 1kΩVoltage Gain: Any value from 80 to 400Lower Cutoff Frequency: 100 HzSinusoidal source (zero internal resistance): 50mVp-pTransistor: Si, β = 75 • Base-Collector capacitance = 8pF • Base-Emitter Capacitance = 25pF a) compute for the biasing resistances.b) determine the dc transistor terminal voltages and transistor currents.
In the circuit in the figure IDSS = 12 mA, VP = -8 V, VGSQ = -2.4 V, IDQ = 4.12 mA, Rsig = 10 kΩ, RG = 100 kΩ, RD = 2 kΩ, RS = 470 Ω, RL = 23.7 kΩ and it is known that rd = 20 kΩ. What will be the voltage gain of the circuit? NOTE: The FET output impedance is rd = 20 kΩ and must be taken into account in the calculations.
Coonsider the common emitter amplifier shown in figure below. Assume a β of 100, VBE = 0.7V, VT = 25mA and VA = 100V. Draw an equivalent DC model and determine the rπ, transconductance (gm) and ro. Draw an equaivalent AC model using the small-signal model Find an expression for vbe and vo in terms of the input voltage
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
Assume the saturation mode and solve for the Q point. Find VGSQ, IDQ, and VDSQ. Given VTN = 1.0 V and Kn = 2 mA/V^2
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
(a) What is the output current IO in the circuitshown if −VEE = −10 V andR = 20 ohm? Assume that the MOSFET is saturated.(b) What is the minimum voltage VDDneeded to saturate the MOSFET if VTN = 2.5 Vand K'n = 0.25 A/V2. (c) What must be the powerdissipation ratings of resistor R and the FET.
Q3:Choose One of the following: : (A)In common emmiter voltage divider bias of BJT, Vcc = 25V; R1= 10 k ohm; R2, = 2.2 k ohm ;Rc = 3.6 k ohm and RE = 1 k ohm.Determain Vec at ß = 120.using Exact analysis Draw the equvelent circuit inaddition the DC load line curve . (B)For self bais(Emitter resistace bais) of BJT,Vcc= 22 V, lb = 45macroA, a = 0.99, RE = 1 k ohm. Determain VCe Draw the equvelent circuit inaddition to DC load line curve.
Current and impedance levels of push-pull RF amplifier. Solid-state RF power amplifiers that provide more than 50 W or so must deal with very large currents, because the typical silicon RF BJT or PET cannot with-stand a DC collector voltage higher than about 40V. (Newer devices using materials such as silicon carbide can exceed this voltage limitation and provide greater power for the same current level.) Suppose a push-pull RF amplifier using a DC collector voltage of 36 V must provide a total peak RF output power of 200W. Typically, the AC "swing" (peak-to-peak AC excursion) of voltage at the collectors cannot exceed twice the DC power-supply voltage. (a) If each of the two devices in the push-pull amplifier delivers IOOW and has a peak-to-peak voltage of (2 x 36) = 72 V across its output terminals , what is the peak current I at the collector of each device, assuming . "d C(PK) smus01 al voltage and current? (b) At this current IC<PK >' how much series inductance L at a…
1. Use the figure below to solve following questions (a) Solve the following dc quantitiesi. VB(Q1)ii. VE(Q1)iii. IE(Q1)iv. VC(Q1)v. VB(Q2)vi. VE(Q2)vii. IE(Q2)viii. VC(Q2)(b) Suppose that the emitter follower is omitted and the output from thecollector of Q1 is capacitively coupled to the 250Ω load, RL. What isthe output voltage across the 250Ω load?
In the circuit given in the figure, what is the voltage gain (Av) of the circuit when = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 15 kΩ and RL = 166 kΩ?NOTE-1: The output impedance r0 of the transistor will be taken into the calculations.NOTE-2: Capacitors are negligible at mid-band frequency.