An engine developing 40 hp at 1250 rpm is fitted with a cone clutch built into the flywheel. The con a face angle of 12.5 degrees and a mean diameter of 14 in. The coefficient of friction ta 0.20 and the n pressure on the clutch face is not to exceed 12 psl. Determine the required face width and the force m sary to engage the clutch, assuming uniform wear. Ans. 2.96 in.. 592 lb

An engine developing 40 hp at 1250 rpm is fitted with a cone clutch built into the flywheel. The con a face angle of 12.5 degrees and a mean diameter of 14 in. The coefficient of friction ta 0.20 and the n pressure on the clutch face is not to exceed 12 psl. Determine the required face width and the force m sary to engage the clutch, assuming uniform wear. Ans. 2.96 in.. 592 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.4P: The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical...

See similar textbooks

Similar questions

The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
the 31mm diameter screw has a double square theread with pitch of 6 mm and a lead of 12 mm .the screw and it's mating threads in the fixed block are graphite- lubricated and have a friction coefficient of 0.09. M=51N.m is applied to the right-hand portion of the shaft , determine (a) the force P required to advance the shaft to the right (b) the force P which would allow the shaft to move to the left at constant speed
Determine the axial spring force necessary to engage the clutch, when an engine developing 30kW at 500 r.p.m. is fitted with a cone clutch built inside the flywheel. The cone has a face angle of 13.5o and a maximum mean diameter of 300 mm. The coefficient of friction is 0.25. The normal pressure on the clutch face is not to exceed 0.1 N/mm2
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.
A band brake is installed on a drum rotating at 250 rpm, and a diameter of 900 mm. The angle of contact is 1.5 pi radians and one end of the brake band is fastened to a fixed pin while the other end of the brake arm is 150 mm from the fixed pin. The coefficient of friction is 0.25 and the straight brake arm is 1000 mm long and is placed perpendicular to the diameter bisecting the angle of contact. Determine the net band pull in kN applied at the end of the brake arm if 50 kW is being absorbed.
1. A triple-thread Acme-form power screw of 50 mm major diameter is used. The nut makes 1.5 turn per cm of axial travel. A force of 600 N is applied at the end of a 850 mm wrench used on the nut. The mean diameter of the collar is 90 mm. If the coefficient of friction at the thread and at the collar are 0.15 and 0.13, respectively. Determine the weight that is being lifted.
The frictional coefficient has a value of 0.26795, and the normal force is 20kN. Determine the angle of friction.
The required clamping force at the board A is to be 1.7 kN . The square-threaded screw has a mean radius of 10 mm and a lead of 3 mm, and the coefficient of static friction is 0.3. (Figure 1) Determine the torque M that must be applied to the screw to tighten it down. Express your answer to three significant figures and include the appropriate units.