5. An engine trom a quary vehicle used in the Buid a Beach program of DEMR has apower requirement of 560 kw. Per hour of its operation. it ejects 234 MJ into itssuroundings at 50 °C. If it behaves like a Carnot engine, answer the questions below.a. How much work (MJ) s done by the engine per hour?b. What is the efficiency (%) of the engine?c. What is the temperature ("C) of the hot reservoir?

A Carnot engine is referred as a thermodynamic cycle which can result in at most efficiency of a…

An engine from a quany vehicle used in the Buid a Beach program of DEMR has a power requirement of 560 kw. Per hour of its operation, it ejects 234 MJ into its suroundings at 50 C. It it behaves like a Cornot engine, answer the questions below. a. How much work (MJ) is done by the engine per hour? b. What is the efficiency (%) of the engine? c. What is the temperature ("C) of the hot reservoir?

An engine from a quany vehicle used in the Buid a Beach program of DEMR has a power requirement of 560 kw. Per hour of its operation, it ejects 234 MJ into its suroundings at 50 C. It it behaves like a Cornot engine, answer the questions below. a. How much work (MJ) is done by the engine per hour? b. What is the efficiency (%) of the engine? c. What is the temperature ("C) of the hot reservoir?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 30RQ: A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center,...

See similar textbooks

Similar questions

A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center, the gas is initially at 10 psig, 65F, and 10.5 in3. After compression and when the piston is at top dead center, the gas is 180Fand occupies 1.5 in3. What would be the new pressure of the gas in psig?
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
a steam engine operation between 150C and 550C. ehat is theorithical maximum thermal effciency?
Steam engine with incomplete expansion receives saturated steam at 1.04 Mpa,expands it to 0.105 Mpa where release occurs. Exhaust is to a condenser at 40C.The actual engine uses 6070 kg/h of steam; it has a brake engine efficiency of 60%and a mechanical efficiency of 85%. The electric generator which it drives has anefficiency of 925. (a) For the ideal engine, find the thermal efficiency and the mep.For the actual engine, determine (b) the brake work in kW and the brake thermalefficiency, (c) the indicated work in kW, indicated thermal efficiency and indicatedsteam rate, (d) the combined thermal efficiency and the combined steam rate
6- Why thermal efficiency of diesel engine is more than petrol engine? 7- Discuss results?
7. Steam at 7.2 MPa, 600OC expands in a Rankine turbine to 0.45 MPa. For 180 kg/s of steam, determine the work, the thermal efficiency, and the steam rate (a) for the cycle, (b) for the turbine with the same specifications, the brake steam is 7.40 kg/kW-h and the driven electric generator has an efficiency of 91%. (c) Find eb, nb, WK, and quality or actual exhaust steam. Please answer letter c. Thanks
A two stage compressor with first stage piston displacement of 94,390 cu.m/sec is driven by a motor. Motor output is 35 HP, suction temperature 22 degC, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105deg C and 44 degC, respectively. Final discharge pressure is 100 psi gage, while suctionis estimated to be 14.4 psi. Determine the compression efficiency.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
A diesel power station has a fuel consumption of 0.37 lb/kWh, the calorific value of fuel being 20,000 BTU/lb. Determine the engine efficiency if the generator efficiency is 95% neglect brake power on the engine.
The compression ratio of an Otto cycle is 8, at the beginning of the zanthropic compression process, the pressure of the air is 100 kPa, the temperature is 27 "C, the volume is 550 cm. At the end of the lzantropic expansion process, the temperature of the air is 700 K. Using the specific temperature values at room temperature (according to the cold air standard assumptions) Find the gravity of the air.
Efficiency of the same engine using regular gasoline at density of 0.71g/cm3 at 11.355L/hr resulting in 14.9kW of power?
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?