An expression for the laminar velocity profile on a flat plate is u=C1sin(C2y)+C3 Where the argument of the sine function is in radians. Using the three common physical conditions that the velocity profile should satisfy, determine d) the skin friction coefficient, Cf as a function of length e) displacement thickness (δ*/x) as a function of length f) the momentum thickness (θ/x) as a function of length g) the drag force (FD) on both sides of the plate

An expression for the laminar velocity profile on a flat plate is u=C1sin(C2y)+C3 Where the argument of the sine function is in radians. Using the three common physical conditions that the velocity profile should satisfy, determine d) the skin friction coefficient, Cf as a function of length e) displacement thickness (δ*/x) as a function of length f) the momentum thickness (θ/x) as a function of length g) the drag force (FD) on both sides of the plate

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.33P

See similar textbooks

Similar questions

When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the weight of the sphere is balanced by the buoyant force and the frictional resistance of the fluid. Make a dimensional analysis of this problem and indicate how experimental data for this problem could be correlated. Neglect compressibility effects and the influence of surface roughness.
An expression for the laminar velocity profile on a flat plate is u=C1sin(C2y)+C3 Where the argument of the sine function is in radians. Using the three common physicalconditions that the velocity profile should satisfy, determine a) the constants C1, C2, and C3.b) the nondimensional velocity profilec) the boundary thickness (δ/x) as a function of lengthd) the skin friction coefficient, Cf as a function of lengthe) displacement thickness (δ*/x) as a function of lengthf) the momentum thickness (θ/x) as a function of lengthg) the drag force (FD) on both sides of the plate
Two endlessly long flat plates, separated by 3 inches in distance but with a thickness of 5 inches, each transport alcohol (5 m/s, 1 Pa·s, S.G. 0.89 (ref. water at 4 degrees Celsius) to a given location with a specific velocity. Prove that the Reynold's number of the following problem is a value approximately around 90-100.
An aluminum sphere of radius 0.5 mm falls through a viscous liquid of density 2700 kg/m3. It attains a constant terminal velocity of 1.5 cm/s. What is the viscosity of the fluid? a) 0.001 N.s/m2 b) 0.052 N.s/m2 c) 0.25 N.s/m2 d) none of these
A square block weighing 1.1 KN and 250 mm on an edge slides down an 20 degrees inclined on a film of oil 6.0 micrometer thick. Assuming a linear velocity profile in the oil, what is the terminal speed of the block in m/s. The viscosity of the oil is 7 mPa-s. a.5.16 b.5.62 c.5.75 d.5.48
1. A unknown 30°C liquid (S.G. = 0.85) flows into a surface which creates a shear stress of 0.20 N/m2 and velocity gradient of 16.8 s-1. What is the kinematic viscosity of the liquid? Express answer in exponential notation w/ 4 significant digits. 2. A unknown fluid at 20ºC fills the follow portion of a sleeve with a inner diameter of 11.8 cm and has a fixed coaxial cylinder of diameter 11.6 cm which rotates at 120 rpm. The torque generated is 23.40084214 N∙m per meter of rod length. What is the fluid used and its kinematic viscosity?
Liquid biofuel (density= 789 kg/m3) is being pumped from a storage tank through a pipe with 1-inch innerdiameter (ID). The fuel is being pumped at a rate of 3.00 gallons per minute. In this process, what is thekinetic energy transport rate (Ėk) in units of horsepower (hp) and ft•lbf/sec.
A cylindrical tank shown below has a radius ? and a circular orifice at the bottom of radius ?. At time ? = 0 the liquid level in the tank is ho. (a) Use the Bernoulli equation to determine the relations between the orifice velocity ?o and the free surface velocity ?s (assume the surface velocity is not zero). (b) Use conservation of mass to determine the orifice velocity in terms of the free surface velocity. (c) Use the results in (a) and (b) to derive a differential equation for h(?). Note that ?s = − dh/dt. d) Separate variables and solve the equation for h(?) with the initial condition h(0) = ho (e) Determine how long it will take to empty the tank.
What is the behavior of flow if water at 20 deg C is flowing through a pipe with a radius of 2.067 in at 20 gal/min. Viscosity of water at 20 deg C =1.005 cP Density of water at 20 deg C = 998.23 kg/m3
A nuclear reactor is cooled by liquid sodium. The liquid sodium has the following properties: dynamic viscosity = 0.41 mPa·s, specific heat capacity = 1.2 kJ/kgK, thermal conductivity 82 W/mK. Which of the following statements is correct for this scenario? please explain A The thermal boundary layer is thicker than the hydraulic boundary layer. B Heat is transferred through the fluid more easily than momentum. C The velocity varies significantly from the surface to the thickness of the thermal boundary layer. D The hydraulic boundary layer is thicker than the thermal boundary layer.
A pitot-static tube to be used in 2n airplane for on-flight measurement was calibrated on ground by using air of density 1.20 kg/m? . A measurement taken at an altitude of 3000 m where the ambient pressure and density were 70 kPa (abs) and 0.91 kg/m? respectively, indicated a velocity of 200 m/s by using the above ‘ground level calibration. Estimate the true speed of the airplane [Take k = 1.4 2nd R = 287 J(kg K
A spherical rain drop of diameter D falls at its terminal velocity V in air of density ρa and viscosity µa. The raindrop has a drag coefficient given by where FD is the drag force acting on the drop and Re is the Reynolds number based on the drop diameter. What is V when ρa = 1.2 kg/m3 , µa = 18 × 10−6 N.s/m2 , and the density of water ρw = 1000 kg/m3 ? The volume of a sphere is given by πD3/6. State all your assumptions.