An ideal gas Diesel engine, that has an inlet temperature and pressure of 24 UC and 102 kPa respectively with a compression ratio of 22:1. The maximum cycle temperature is 1,260 UC. Take Specific heat at constant pressure and constant volume for air as 1.005 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the specific heat received to one decimal place and include the correct SI unit (J...).

An ideal gas Diesel engine, that has an inlet temperature and pressure of 24 UC and 102 kPa respectively with a compression ratio of 22:1. The maximum cycle temperature is 1,260 UC. Take Specific heat at constant pressure and constant volume for air as 1.005 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the specific heat received to one decimal place and include the correct SI unit (J...).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Reheat Rankine Cycle Instructions: 1.Solve the Rankine Reheat Cycle problem below. 2. Draw a detailed Ts Diagram. Must be clear and readable. 3.Show and follow step by step procedure of solution In an ideal reheat cycle, the steam throttled condition is 9MPa and 480 oC. The steam is then reheated to 2MPa and 460 oC. If turbine exhaust is 60 oC, Determine cycle efficiency. ( Draw the Ts Diagram)
Essay type: (25+ wordcount) Consider the ideal Otto, Diesel, Ericson, Stirling, and Carnot cycle operating between the same temperature limits. How would you compare the thermal efficiencies of these five cycles?
Thermodynamics (Brayton Cycle) Round up the answer up to 5 decimal places. A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following: a. Pressure & temperature at each stateb. T-S diagramc. Heat Added, per unit massd. Thermal Efficiencye. Mass flow rate, kg/min
how to make a low temperature stirling engine step by step assessment ?
Engine specification gives the physical features and performance characteristics of an engine in terms of power, fuel consumption and efficiency.
Instructions: Perform a cycle analysis for the given reheat-regenerative Rankine cycles. Supply the table with the necessary equations based on enthalpy and mass fraction of working fluid’s state points.
Draw the schematic or plant layout. Draw the T-s diagram Mandatory: A, B, C Suggested: D, E A reheat cycle has the following data: Throttle, 8.5 MPa at 400°C Turbine exhaust, 0.06 MPa For an ideal cycle, determine the: (A) Work (B) Thermal efficiency (C) Heat rate (D) What is the thermal efficiency of the corresponding Rankine cycle? (E) What is the percent improvement in engine heat rate of the reheat cycle from the Rankine cycle.
Completely solve and box the final answers. Write legibly 2. (a) Draw the cycle with designated given values and (b) determine the mass flow rate of an ideal Brayton gas cycle of an air produces a workload of 220,000 watts, the temperature at the beginning of an isentropic compression is 280°C and constant heat addition of 827°C, the cut off ratio of 1 to 10.
question 1) 1. Describe how the mean effective pressure for reciprocating engines is defined and its importance for thermodynamic analysis of internal combustion engines.
Part A only A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve the problems below using the variable specific heat assumption Part ( A) Plot the cycle on the T–s, P–s, and T–v diagrams.
Subject: thermodynamics In a gas turbine generating set, two stages of compression are used with an intercooler between stages. The HP turbine drives the HP compressor, and the LP turbine drives the LP compressor and the generator. The exhaust from the LP turbine passes through a heat exchanger which transfers heat to the air leaving the HP compressor. There is a reheat combustion chamber between turbine stages which raises the gas temperature to 600 ?C, which is also the gas temperature at entry to the HP turbine. The overall pressure ratio is 10/1, each compressor having the same pressure ratio, and the air temperature at entry to the unit is 20 ?C. The heat exchanger thermal ratio may be taken as 0.7, and intercooling is complete between compressor stages. Assume isentropic efficiencies of 0.8 for both compressor stages, and 0.85 for both turbine stages, and that 2% of the work of each turbine is used in overcoming friction. Neglecting all losses in pressure, and assuming that…
Question 12(Please provide a hand written solution) Air flows through an Otto Cycle, beginning the compression process at a temperature of 50 ˚C. The volume of gas present in the cylinder at the start of compression is 0.001 m3. During the heat addition process, 1200 kJ/kg of heat is added to the air. The compression ratio of the cycle is 8.5. Using cold-air standard analysis;Calculate the temperatures at the other states in the cycleWrite the equation and sample to determine the mass,Write the equation and sample to determine the net work,Write the equation and sample to determine the thermal efficiency,Write the equation and sample to determine the volume at the end of the compression,Write the equation or sample to determine the Mean effective pressure, andPlot the work produced during one cycle, the maximum pressure in the cycle, the thermal efficiency of the cycle, and the mean effective pressure for pressures at the beginning of compression ranging between 50 kPa and 150 kPa,…