An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 100 kPa and 17°c, and 800 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Determine (a) the maximum temperature and pressure that occur during the cycle, (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle. (e) Also, determine the power output from the cycle, in kW, for an engine speed of 4000 rpm (rev/min). Assume that this cycle is operated on an engine that has four cylinders with a total displacement volume of 1.6 L. Assume constant Cv = 0.716 kJ/kgK and k=1.4.

An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 100 kPa and 17°c, and 800 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Determine (a) the maximum temperature and pressure that occur during the cycle, (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle. (e) Also, determine the power output from the cycle, in kW, for an engine speed of 4000 rpm (rev/min). Assume that this cycle is operated on an engine that has four cylinders with a total displacement volume of 1.6 L. Assume constant Cv = 0.716 kJ/kgK and k=1.4.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 100 kPa and 17C, and 800 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Accounting for the variation of specific heats of air with temperature, determine (a) the maximum temperature and pressure that occur during the cycle, (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle. (e) Also, determine the power output from the cycle, in kW, for an engine speed of 4000 rpm (rev/min). Assume that this cycle is operated on an engine that has four cylinders with a total displacement volume of 1.6 L.
Consider an ideal Otto cycle with cold-air-standard assumptions, and compression ratio of 14. The temperature and pressure at the beginning of the compression process are 350K and 0.2 MPa. The maximum air temperature in the cycle is found to be 2000K. Determine: the temperature and pressure at the end of each process of the cycle Determine: the thermal efficiency of the cycle Determine: the mean effective pressure of the cycle Determine: the entropy change per unit mass for the heat addition and heat rejection process
The temperature of air at the beginning of compression in an Otto cycle is 310 K and maximum temperature in the cycle is 2200 K. If the pressure at the end of adiabatic compression is 15 times that at the start, determine the compression ratio, thermal efficiency, and work done. Take k for air = 1.4.
Air enters the compressor of a gas turbine at 100 kPa and 25°C. Determine the back work rate and thermal efficiency of the Brayton cycle for a pressure ratio of 5 and a maximum temperature of 850°C.
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 750 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Taking into account the variation of specific heats with temperature, determine the pressure and temperature at the end of the heat-addition process.
Consider an air-standard Otto cycle that has a compression ratio of 9.0 and a heat addition of 870 Btu/lbm. If the pressure and temperature at the beginning of the compression process are 14.0 psia and 40 °F, determine a. the maximum pressure and temperature for the cycle, b. the thermal efficiency, and c. the mean effective pressure, in psia
Air is used as the working fluid in a simple ideal Brayton cycle that has a pressure ratio of 12, a compressor inlet temperature of 300 K, and a turbine inlet temperature of 1000 K. Determine the required mass flow rate of air for a net power output of 70 MW, assuming both the compressor and the turbine have an isentropic efficiency of 100 percent.
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 100 kPa and 17°C, and 800 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Accounting for the variation of specific heats of air with temperature, determine (a) the maximum temperature and pressure that occur during the cycle, (b) the net work output.
Question 1 [20]Air at the beginning of an ideal Otto cycle is at 101.3 kPa and 15°C. The cycle has acompression ratio of 7, and 1000 kJ/kg of heat is transferred to air during the constantvolume heat-addition process. Using constant specific heats at room temperature, calculate,1.1 the pressure and temperature at the end of the heat- addition process,1.2 the net work output,1.3 the thermal efficiency, and1.4 the mean effective pressure for the cycle.
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 100 kPa and 17°C, and 800 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Accounting for the variation of specific heats of air with temperature, determine the thermal efficiency.
OTTO CYCLE The compression ratio of an ideal Otto cycle is 8. Air is 95 kPa and 27 Celsius at the start of thecompression operation, and 750 kJ/kg of heat is transferred to air during the constant-volumeheat-addition process. The variation of specific heats with temperature, determine (a) the pressure and temperature at the end of the heat-addition process, (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle. Show complete solution.
An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 105 kPa and 28 °C, and 850 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Taking into account the variation of specific heats with temperature, determine (i) the pressure and temperature at the end of the heat addition process, (ii) the net work output, (iii) the thermal efficiency, and (iv) the mean effective pressure for the cycle.