An impact test was done on specimen M and R and the results are shown in Fig. Q2(c) and Table Q2(c). Based on the obtained results, choose whether specimen M or R is brittle or ductile in terms of: Impact strength Fracture surface Specimen M Specimen Impact Strength (J/m²) Fig. Q2(c) Table Q2(c) M 4.35 x 105 Specimen R R 1.21 x 106

An impact test was done on specimen M and R and the results are shown in Fig. Q2(c) and Table Q2(c). Based on the obtained results, choose whether specimen M or R is brittle or ductile in terms of: Impact strength Fracture surface Specimen M Specimen Impact Strength (J/m²) Fig. Q2(c) Table Q2(c) M 4.35 x 105 Specimen R R 1.21 x 106

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 147 kN. - Length of the specimen is 28 mm. - The yield strength is 75 kN/mm2. - The percentage of elongation is 49 %. Determine the following iii) Stress under an elastic load of 16 kN, iv) Young's Modulus if the elongation is 1 mm at 16 kN and (v) Final diameter if the percentage of reduction in area is 22 %. I wont answer for this three questions only: 1)Final Area of the Specimen at Fracture (in mm) 2)Final Diameter of the Specimen after Fracture (in mm) 3)Initial Cross-sectional Area (in mm2)
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 66 % - Percentage of Reduction in Area = 38 % - Final length after fracture = 34.6 mm - Final Diameter after fracture = 4.43 mm & - Ultimate stress = 364 MPa Determine the Initial length, Initial diameter and Maximum load. ii) Final Area (in mm2) = iii) Initial Area (in mm2) =
A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 10^6 psi. Find Poisson’s ratio for the specimen. a. 0.40 b. 0.95 c. 0.30 d. 0.33 Show complete solutions when answering
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 60 % - Percentage of Reduction in Area = 36 % - Final length after fracture = 35.2 mm - Final Diameter after fracture = 3.54 mm & - Ultimate stress = 439 MPa i) Initial Length (in mm) = ii) Final Area (in mm2) = iii) Initial Area (in mm2) =
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 60 % - Percentage of Reduction in Area = 36 % - Final length after fracture = 35.2 mm - Final Diameter after fracture = 3.54 mm & - Ultimate stress = 439 MPa iv) Initial Diameter (in mm) = v) Ultimate Load (in N) =
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 66 % - Percentage of Reduction in Area = 38 % - Final length after fracture = 34.6 mm - Final Diameter after fracture = 4.43 mm & - Ultimate stress = 364 1) Final Area (in mm2) = 2) Initial Area (in mm2) = 3) Ultimate Load (in N) =
a) Compression tests are generally performed on brittle materials-why?b) How a cast iron specimen fails under compression load?c) Define secant modulus?
Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 65 % - Percentage of Reduction in Area = 39 % - Final length after fracture = 36.1 mm - Final Diameter after fracture = 4.25 mm & - Ultimate stress = 401 MPa SOLUTION: Initial Diameter (in mm) = Ultimate Load (in N) =
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 65 % - Percentage of Reduction in Area = 39 % - Final length after fracture = 36.1 mm - Final Diameter after fracture = 4.25 mm & - Ultimate stress = 401 MPa SOLUTION: Initial Length (in mm) = Final Area (in mm2) = Initial Area (in mm2) =
The following engineering tensile properties are given for the 1080 steel:-Yield strength (MPa): 585-Tensile strength (MPa): 965-Elongation to fracture for specimen of 5cm gage length (%): 12A 5cm long circular rod of 1080 steel specimen with a diameter of 1.28cm isloaded to failure in tension. a) What was the maximum load needed to break the specimen?(20 points)b) If necking initiated at 80% of the total elongation, prior to this point thespecimen deformation is uniform, compute the true stress at the point ofnecking initiation.
A torsion test shows that the shear modulus of an aluminum specimen is 27.6 GPa. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 73.2 GPa. Find the Poisson’s ratio for the specimen.