An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from the surface. Given dry unit weight = 18KN/m3, c' = 12kN/m2, angle of friction = 23.5 degree and saturated unit weight = 23kN/m3. Calculate the slope factor of safety if %3D %3D %3D (i) water table exists far from the slip line O 0.72 O 1.02 О 1.32 O 1.62 (ii) water table exists at the ground surface О 04 O 0.8 O 1.2 О 1.6

An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from the surface. Given dry unit weight = 18KN/m3, c' = 12kN/m2, angle of friction = 23.5 degree and saturated unit weight = 23kN/m3. Calculate the slope factor of safety if %3D %3D %3D (i) water table exists far from the slip line O 0.72 O 1.02 О 1.32 O 1.62 (ii) water table exists at the ground surface О 04 O 0.8 O 1.2 О 1.6

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.5P

See similar textbooks

Similar questions

An infinite slope is inclined at 22 degree. A plane of failure has developed at depth of 8 m from the surface. Given dry unit weight = 18kN/m3, c’ = 12kN/m2, angle of friction = 23.5 degree and saturated unit weight = 23kN/m3. Calculate the slope factor of safety if: (i) water table exists far from the slip line
An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.
A long slope is made up of a cohesionless soil with the internal friction angle of 34°. If the water table rises to the surface of the slope, then determine the maximum possible value of the slope angle to get a factor of safety of 1.5. Take saturated unit weight as 18 kN/m3 and the unit weight of water as 10 kN/m3.
A cement lined rectangular channel 6m wide carries water at the rate of 30m3/s. Find the value of Manning’s constant, if the slope required to maintain a depth of 1.5m is 0.00118.
3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.
Given an infinite slope with the following properties: γ = 17 kN/m3, H = 5 m, β = 34°, φ = 25° and c = 20 kPa. a. Determine the normal stress. b. Determine the shear stress. c. Determine the factor of safety.
1. A trapezoidal channel with a 5-m bottom width and side slope m = 1.0 discharges 35 m3/s. The slope is 0.004 and is paved with smooth concrete (n = 0.012). a. What is the critical depth? b. What is the normal depth? c. Is it a mild slope, or steep?Hint: Compare critical depth with normal depth OR find the critical slope (??) and compare it with bed slope(?0) d. Is the depth increasing or decreasing upstream? Why would that be (e.g. a spillway, dam, etc.)?Hint: For the first part, use ????=?0−?1−??2 to show if the depth is decreasing/increasing (either by finding Fr and S, OR by simply using the values of ?, ?? and ?0 to figure out if the fraction is +/-). e. How would you conceptualize the flow – what regime (e.g., S1, S2, S3, M1, M2, M3 in Figure 10.20)? f. Determine the depth 3.3 m upstream from a section that has a measured depth of 1.69 m.Hint: If you are using MATLAB, solve the GVF differential equation (????=?0−?1−??2) and find flow depth y at location x = -3.3 m. If you are…