An integrator circuit A) uses a resistor in its feedback circuit B) uses an inductor in its feedback circuit C uses a capacitor in its feedback circuit D uses a resistor in its feedback circuit or uses a capacitor in its feedback circuit The common-mode voltage gain of a diff amp is equal to Rc divided by ____. (A) r/2 B 2re C) 2RE D) re Compared to a bipolar transistor, the JFET has a much higher. A current (B) voltage gain supply voltage D input resistance

An integrator circuit A) uses a resistor in its feedback circuit B) uses an inductor in its feedback circuit C uses a capacitor in its feedback circuit D uses a resistor in its feedback circuit or uses a capacitor in its feedback circuit The common-mode voltage gain of a diff amp is equal to Rc divided by ____. (A) r/2 B 2re C) 2RE D) re Compared to a bipolar transistor, the JFET has a much higher. A current (B) voltage gain supply voltage D input resistance

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

3. For the circuit below, find the following: 3.1 Find Vo in terms of Va and Vb 3.2 If Va = 5V and Vb= -4V, find Vo. 3.3 Sketch Vo as a function of Va (Vo vs. Va) when the power supplies on the op- amp are ±12V and Vb = 4V. Clearly mark the two intercepts and the saturation points, if any. 3.4 If the power supplies on the op-amp are ±12V and Vb = 4V, what is the range of Va that allows the op-amp to have a linear output? (Hint: refer to the graph you drew in part 3.3)
As shown is the ramp generator for an integrating converter. (a) If the offset voltage of the op amp is 10 mV and V = 3 V, what is the effective reference voltage of this converter? (b) The integrator is used in a single-slope converter with an integration time of 1/30 s and a full-scale voltage of 5.12 V. What is the RC time constant? If R = 50 kΩ, what is the value of C?
A students working operational amplifier in such a way that it performs as an integrator and differentiator respectively input voltage 100sint volt is applied for both amplifier at inverting terminalening on in terminal rounded then find following using some Input voltage 1.if input resistance is 200 and capacitance is 50F then calculate the output voltage of integrator 2. if capacitance is 30 microfarad and feedback is 150ohm then calculate the output voltage of Differentiator 3.calculate the ratio of output voltage of integrator to differentiator 4.analyze the nature of output voltage of integrator 5.Analyze the nature of output voltage of differentiator
In the given circuit what is the derivation formula for the magnitude of vf/vo and by using this formula solve for the required gain of the op amp and the required resistance rf to sustain the oscillation. Given: Rr = 15 kΩ C1 = 2.2 nF C2 = 4.7 nF R1 = 47 kΩ R2 = 22 kΩ
Two single-stage capacitively coupled amplifiers like the one in the figure below are connected as a two-stage amplifier (RL is removed from the first stage). Determine whether or not this configuration will operate as a linear amplifier with an input voltage of 10 mV rms. If not, modify the design to achieve maximum gain without distortion. (provide modified design with explanation)
An op-amp with an open-loop gain of 3x106 and Vcc = 12 V has an inverting-input voltage of 6.7 microVolts and a non-inverting input voltage of 5.4 microVolts. What is its output voltage? Be sure to round your answer to the nearest single digital decimal place. Do not enter units. As an example, if you calculate 7.39 Volts then enter 7.4 as your submitted answer
3D Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output of the third stage stage. a.9 V b.9000 mV c.79.2 V d.792 mV
Help me with the following multiple choices questions : 1.Current cannot flow to ground through ______ A.an ordinary ground B.a virtual ground C.a mechanical ground D.an a.c ground 2.For an OP-amp with negative feedback, the output is .... A. fed back to the noninverting input B. fed back to the inverting input C.equal to the input D.increased 3. A certain inverting amplifier has a closed loop voltage gain of 25. The OP-amp has an open-loop voltage gain of 100,000. If an OP-amp with an open-loop voltage gain of 200,000 is substituted in the arrangement, the closed-loop gain________ A. remains at 25 B. doubles C. increases slightly D. drops to 12.5
A signal source with an open-circuit voltage of Vs= 2 mV rms and an internal resistance of 60 kΩ is connected to the input terminals of an amplifier having an open-circuit voltage gain of 100, an input resistance of 115 kΩ , and an output resistance of 4 Ω. A 4 Ω load is connected to the output terminals. a) Find the current gain. Express your answer using three significant figures. b) Find the power gain. Express your answer using three significant figures.
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
Design a three-stage amplifier that is impedance matched (use an emitter follower in stage 2) with an overall voltage gain of approximately 400. The phase of the input and output signal should be maintained. The amplifier should have a usable bandwidth of approximately 20MHz. As engineers you are expected to provide mathematical calculations, circuit diagrams and simulations in multisim software. The simulations should show a sample input signal, its output signal and frequency response plot of the three-stage amplifier.
As, we have learned during the lectures that an op amp combined with a balanced resistance bridge helps the circuit to achieve R. =∞ through the positive feedback action. Describe anyother approach(s) to achieve the output resistance R. =∞ to in a transconductance amplifiers or V-I converter. Note: You don't need to explain the balanced bridge