MAB orque in pound-feet. The inrush current to a synchronous motor is 235 amp when it is started from a rated-voltage source of 2,200. What per cent tap on a compensator should be used if the starting current on the line side is to h limited to 100 amp? What vo.tage will be impressed upon the motor at the starting instant? WZL

MAB orque in pound-feet. The inrush current to a synchronous motor is 235 amp when it is started from a rated-voltage source of 2,200. What per cent tap on a compensator should be used if the starting current on the line side is to h limited to 100 amp? What vo.tage will be impressed upon the motor at the starting instant? WZL

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

Branch-circuit conductors supplying a single continuous-duty motor shall have an ampacity not less than _____ rating A. 125% of the motor’s nameplate current B. 125% of the motors full-load current as determined by 430.6(a)(1) C. 125% of the motor’s full locked-rotor D. 80% of the motors full-load current.
SHOW YOUR COMPLETE SOLUTION, ANSWER MUST BE IN 2 DECIMAL PLACES. SHOW WHAT IS GIVEN AND WHAT IS THE UNKNOWN. A 20KW short shunt generator with a terminal voltage of 250V has armature, series and shunt field winding have resistances of 0.05 ohms, 0.03 ohms and 100 ohms respectively. Calculate the total voltage generated in the armature when the brush drop is 1 V per brush and the feeder resistance is 0.5 ohm.
please answer asap A 40Kw motor with a heating time constant of 120 minutes has a final temperature rise of 60 degree Celsius on continuous rating. Determine half hour rating for same temperature rise. Motor has maximum efficiency of 80% of full load
You’re powering up a new motor in a brushless motor control system. After moving the shaft of the motor lightly left to right, the motor reverses direction and runs away. What’s the problem? A. Power transistor failureB. Wrong motor typeC. Reversed tachometerD. Reversed hall-effect sensor
A motor is tripping out on overload. The motor nameplate reveals a full load current of 68 amperes. When the motor is operating under load, an ammeter indicates the following: Phase # 1=106 Amps, Phase #2=104 Amps, and Phase #3=105 Amps. The motor has been in service for six months. What is most likely the problem? motor winding is bad ambient temperature is too high and the overload needs to be adjusted to account for that overload setting is too low bearing is bad or the load is too heavy
Determine the temperature of the field winding of a series motor when its resistance had increased to 204 Ω after running for 4 hours. The field winding has a resistance of 114 Ω at 18oC and its temperature coefficient of resistance at 0oC is 0.004/Co. Notes: - Express your answer in 2 decimal places. - No need to include the unit in the answer field. - Final answer should be in oC.
The deep well pump motor is 50 hp, 3-phase, 4-poles, 230 volts, 60 Hz induction motor, operating at 0.90 efficiency, 0.85 power factor and 3 % slip. Determine the current at which the motor is operating. (a). 112.7 A (b). 122.4 A (c). 120. 5 A (d). 124.7 A
17. An a-c hoist motor has the following duty cycle: acceleration, 110 amp for 8 sec; constant speed, 60amp for 18 sec.; lowering and braking, 20 amp for 10 sec; and the rest, 0 amp for 5 sec. The current ratingfor this motor isA. 76.56 amp.B. 69.64 amp.C. 74.09 ampD. 78.29 amp
A220 Vshunt DC motor rotates with speed of1800rev/min.( need handwritten only ,otherwise downvote.)
19. You’re powering up a new motor in a brushless motor control system. After moving the shaft of themotor lightly left to right, the motor reverses direction and runs away. What’s the problem?A. Wrong motor typeB. Reversed tachometerC. Power transistor failure
A single-phase electric motor is connected to a 240-volt, 30-ampere circuit. The motor nameplate indicates that the full-load current draw of the motor is 21 amperes. The motor is connected to an inertia load (a large flywheel) that requires several seconds for the motor to accelerate to full speed. Because of the long starting time, the motor causes the circuit breaker to trip before the load has reached full speed. Your job is to connect a resistor in series with the motor during the starting period that will limit the starting current to 90% of the circuit-breaker rating. An ammeter indicates that the motor has a current draw of 64 amperes when power is first applied to the motor. Determine the ohmic value and wattage rating of the resistor that should be connected in series with the motor during the starting period.
Determine the reduction in the annual energy costs due to staggered duty cycling of three identical 4 pole fan motors rated 30 HP. The motor manufacturer specifies 14 minutes on and 2 minutes off as the minimum duty cycle. Staggered duty cycling approach is considered and at any given time, only two out of the three motors are operating. The utility monthly demand charge is $12/kW. Find: The maximum allowable ON time in minutes Question 11 options: approximately 14 minutes approximately 9 minutes approximately 6 minutes approximately 2 minutes