Please see question in pic thank you An internal combustion engine operates using an ideal gas with Cp35-mol-KIt operates using Brayton cycle with a minimum temperature of350 K and an exhaust temperature of 800 K. The minimum pressure of thecycle is 150 kPa and the compression pressure ratio is 12:1. Refer to the TSdiagram below.T3'33P = constant2.P = constant11 to 2: Compressor2 to 3: Heat Exchange (Heating)3 to 4 (Exhaust) : Turbine4 (Exhaust) to 1: Heat Exchange (Cooling)2'a. Determine the efficiency of the cycleb. Determine the power output of the Brayton Cyclec. Sketch the Brayton cycle, showing the state propertiesT) in the diagram and the energy flows

GivenT1=350KT2=800krp=12Cp=35J/mol-k

Answered: An internal combustion engine operates…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HANDWRITTEN:A vintage car has an engine that operates on an Otto cycle with a compression ratio of 8:1. Using the air standard assumption, the following parameters are applied: T2 = 720 K, T4 = 1890 K. Solve for the (a) percentage clearance, (b) volume displacement, (c) pressure and temperature at each corner, e) Heat added, (f) Heat rejected, and (g) efficiency. Note: Make sure to indicate a CORRECT P-V and T-S diagram
A petrol engine with compression ratio of 15:1 was analysed as an air-standard cycle. The inlet pressure and temperature of the air are 101 kPa and 15 0C respectively while the maximum temperature of the cycle is 1,344 0C. The mass flow rate of air through the engine is 615 kg/min when running at its optimum speed. Thake the specific heat capacites at constant pressure as 1.0038 and 0.714 kJ/kgK. Calculate the thermal efficiency of the cycle power obtainable from the cycle
4. A BMW with 4-stroke 2.0 L Twin Turbocharger 4-cylinder in-line engine is connected to an engine dynamometer which gives a torque reading of 350 Nm at 3800 rpm. The engine is running with volumetric efficiency of 118% and petrol RON95 (C7H₁7) is used as the combustion fuel. At the engine speed of 3800 rpm, the intake air pressure and temperature both are 155 kPa and 38°C. Given the gas constant value R-0.287 kJ/kgK. Calculate: a) Fuel mass flow rate of the engine. b) Brake specific fuel consumption of the engine at 3800 rpm in g/kW.hr.
THERMODYNAMICS The compression ratio of an air-standard dual cycle is 14 and the cutoff ratio is 1.2. During the constant-volume heat addition process, the pressure ratio is 1.5. Determine the thermal efficiency, heat added, maximum gas pressure, and temperature when this cycle is run at 80 kPa and 20 degree celcius at the start of the compression. Make use of the cold-air assumption. Show complete solution on a paper.
At the beginning of the compression process of an air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and mass flow rate in the system is 1900 kg/hr.cp = 1.006 kJ/kg K cv = 0.717 kJ/kg K calculate the thermal efficiency of the cycle in %? Answer to 1 decimal place.
The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2250 K. Assume constant specific heats evaluated at 300 K. Determine the mean effective pressure, in kPa.
An air standard gas turbine engine operates on an overall pressure ratio of 4 and between the temperature limits of 70 F and 1600 F. The efficiencies of compressor and turbine are 0.82 and 0.92, respectively. To modify, a regenerator of effectiveness 0.65 is added and two stage of compressor with intercooler is inserted and two-stage turbine with reheater is inserted. (a) Assuming constant specific heats, evaluate the compressor work (b) calculate the turbine work (c) calculate the thermal efficiencies Show complete solution on a paper.
An ideal Diesel engine operates on 1.5 lb of air with a suction state at 14.1 psia and 100 F. The pressure at the end of compression is 475 psia and the cut -off is 6% of the stroke from head -end dead - center. Using air properties (R=53.34 ft-lbf/Ibm-R, k=1.4, Cp =.24, Cv=. 1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure.
The compression ratio of a Dual cycle is 16. The temperature and pressure at the beginning of the cycle are 1 barand 27C. The maximum pressure of the cycle is limited to 70 bar and heat supplied is limited to 675 kJ/kg of air.Find the temperature at point 3.cp = 1.005, cv = 0.718 and Y = 1.4.
I only need help with letter (d). The answer for letter (a) is 22.87. The answer for letter (b) is 1.9538. The answer for letter (c) is 66.71%. The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2050 K. Assume constant specific heats evaluated at 300 K.Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
An oil engine working on a dual combustion cycle, has a compression ratio of 16: 1 and the cut-off takes place at 6% of the stroke. The maximum pressure obtained is 70 bar. The pressure and temperature at the beginning of compression are 1 bar and 110°C respectively. Determine the pressure and teperature at all the important points of the cycle. Assume R = 0.287 kJ/(kg K) and c, = (0.716+ 125 x 10-67) kJ/(kg K)
A gas turbine power plant working on Brayton cycle as per the following specifications Pressure and temperature of air at inlet to compressor = 1 bar and 10oC Power output of the plant = 8 MW Temperature at inlet to the turbine = 780 oC Pressure ratio = 12 Isentropic efficiency of compressor = 100% Isentropic efficiency of turbine = t(%)= 91 Discuss any three methods to improve performance of the cycle with justification based on the data given in the question

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS