An L-shaped solid round bracket has the properties E, G, A, I, and J. The bracket below is loaded with a torque about the Z-axis at the free end and a force in the Y direction. A) Derive an expression for the deflection of the free end in the Y-direction (Dummy load F=0 shown)? B) Calculate the deflection in the Y-direction if the L-shaped round bracket is made from aluminum with a 12 in, b = 6 in, d = 0.75 in, and T = 30 in-lb. Solid round rod of properties E, G, A, I, and J.

An L-shaped solid round bracket has the properties E, G, A, I, and J. The bracket below is loaded with a torque about the Z-axis at the free end and a force in the Y direction. A) Derive an expression for the deflection of the free end in the Y-direction (Dummy load F=0 shown)? B) Calculate the deflection in the Y-direction if the L-shaped round bracket is made from aluminum with a 12 in, b = 6 in, d = 0.75 in, and T = 30 in-lb. Solid round rod of properties E, G, A, I, and J.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.4P: A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to...

See similar textbooks

Similar questions

Segments A B and BCD of beam A BCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of SO N/m acts on EC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, Y, and Mat x = 5m. (c) Repeat parts (a) and (b) for die case of the roller support at C replaced by a linear spring of stiffness kr™ 200 kN/m (see figure).
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
The figure shows a rectangular member OB, made from 0.5 cm thick aluminum plate, pinned to the ground at one end and supported by a coil spring at point A. The spring has been measured to deflect 1 mm with an applied force of 10 kN. Find the deflection at point B.
A right-angle-cantilevered bracket with concentrated load and torsional loading at the free end is shown in Figure. Using Castigliano’s Theorem, find the deflection at the free end in the z-direction. Neglect transverse shear effects.
3. Find the torsional deflection of a solid steel shaft 100 mm in diameter and 130 mm long subjected to twisting moment of 3 x 106 N-mm. The torsional modulus of elasticity is 80,000 N/mm2.
Using the theorem of Castigliano, find the horizontal (not vertical) deflection of the free end of the cantilever frame shown in the figure duc to the vertieal applied load P. Express your answers in terms of P, l (length), E (modulus of clasticity), A (cross sectional area) and I (moment of inertia of the cross section around the bending axis. Consider only bending and axial loading and assume that the cross-section is circular and that E, A, and I are constant.
Derive the torsional stiffness of a shaft. Also, find its k if outer radius is 0.05 m, inner radius is 0.03 m and the material is brass.
Derive the torsional stiffness of a shaft. Also, find its k if outer radius is 0.05 m, inner radius is 0.03 m and the material is brass. Note: Brass : 40 GPa
A circular Euler column with one end fixed and the other pinned (or hinged or simply-supported) is under a compressive axial load. Given the length L of the column and bending rigidity EI, what is the buckling load Pcr ?
As an engineer in a construction company, you are assigned a new job which is to design a solid, lightweight aluminium alloys column that can withstand compressive load P as shown in the Figure below. By either selecting aluminium 6061 -T6 alloy or 2014- T6 aluminium alloys, Determine the maximum load P if the eccentricity is 40mm and allowable bending stress is 250 MPa. In your design proposal, clearly state the following: i) Material selected ii) Calculated maximum load P using allowable stress method iii) calculated maximum load P using interaction method
(a) In Fig. a6.00-m-long, uniform beam is hangingfrom a point 1.00 m to the rightof its center. The beam weighs 140 Nand makes an angle of 30.0° with thevertical. At the right-hand end of thebeam a 100.0 N weight is hung; anunknown weight w hangs at the leftend. If the system is in equilibrium,what is w? You can ignore the thicknessof the beam. (b) If the beammakes, instead, an angle of 45.0° withthe vertical, what is w?