An NPN BJT is biased in the forward active region. Assume that InE 1.000 mA, IpE = 0.005 m/ Inc = 0.995 mA and Ipc = 0. Calculate the emitter injection efficiency y, the base transport facto B", the common emitter current gain Bdc, the common base current gain ade, respectively.

An NPN BJT is biased in the forward active region. Assume that InE 1.000 mA, IpE = 0.005 m/ Inc = 0.995 mA and Ipc = 0. Calculate the emitter injection efficiency y, the base transport facto B", the common emitter current gain Bdc, the common base current gain ade, respectively.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A depletion-mode NMOS transistor has VTO =−1.5 V, 2φF = 0.75 V, and γ = 1.5√V. Whatsource-bulk…

A: Write the given values in the question.

Q: In the circuit given below, VDD = 20 V and IDSS = 20 mA and Vp = -1 V for both transistors (T1 and…

A: In the circuit given , VDD = 20 V and IDSS = 20 mA and Vp = -1 V for both transistors (T1 and T2).…

Q: Determine the operating point of the BJT given that measure terminal voltages are: VE = OV VB = 0.7V…

A: Operating point is the dc value we used for biasing that mean in which region we require transistor…

Q: Derive an expression for gm, in terms of K, Vto, VGSQ, and IDQ for an NMOS transistor operating in…

A: The drain current in the triode region is equal to: The Transconductance is equal to the partial…

Q: The figure below shows NMOS and PMOS devices with drain, source, and gate ports annotated. Determine…

Q: Calculate the drain current in an NMOS transistorfor VGS = 0, 1 V, 2 V, and 3 V, with VDS = 4 V,if W…

A: When VGS is less then the VTN, the drain current will be zero as the device is in cut-off region.…

Q: An E-MOSFET has these values: ID(active) = 1 mA and Vps(active) = 10 V. What does its drain…

A: We need to find out drain resistance .

Q: (a) Qualitatively sketch the inversion charge density in the channel region when an NMOS transistor…

Q: Find the current gain, hEE = B, for a commercially available transistor. a. What is the approximate…

Q: An n-channel JFET is described by IDSS = 2.5 mA, VP = − 2 V, and λ = 0.025 V−1 What are the values…

A: GIVEN:

Q: Suppose we have an NMOS transistor that has gm=2 mS and rd=5 kΩ for a Q point of and VGSQ = 2 V, IDQ…

A: Write the slop of the given NMOS transistor in range for 9 < vDS < 11, It means that for…

Q: Calculate the drain current in an NMOS transistor if Kn = 250 μA/V2 , VTN = 0.75 V, λ =0.02 V−1, VGS…

A: Given data: VTN is: 0.75 V VGS is: 5 V VDS is: 6 V The expression for the drain current is given…

Q: XProblem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (Vcc) at…

A: First we will find out the Current then we will find out voltage

Q: The common-emitter gain of a BJT operating as a voltage-controlled current source is ß = 450. If the…

A: Given data, Current gain, β=450. Collector current ic=1 mA.

Q: VDD Ca Ra RL Given Rsig = 19Kohm, RG-148Kohm, RL=3Kohm, and the transistor(VTN=1.2V) operating at…

A: From given drain current, gate to source voltage and threshold voltage we will find conduction…

Q: Suppose we have a certain pnp transistor that has VCE = −5 V, IC = 0.995 mA, and IE = 1.000 mA.…

Q: For the circuit given below, you are required to find and answer the following. 1) What is the…

A: Ans (1) Q point of the device, is also known as the bias point is a steady-states DC voltages or a…

Q: Calculate the drain current for an NMOS transistor operating with VGS = 5 V and VDS = 10 V if VTN =…

A: Given data: VTN is: 1 V VGS is: 5 V VDS is: 10 V The expression for the drain current is given…

Q: A PMOS transistor is operating with VBS = 0 V,VGS = −1.5 V, and VDS = −0.5 V. What are the region of…

Q: A B C w'w* w w

Q: Problem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (Vcc) at…

A: To calculate collector voltage Vc

Q: xProblem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (vcc) at…

A: We need to find out collector terminal voltage for given details .

Q: For an n-channel MOSFET biased in the saturation region, the parameters e k = 100 μA/V², VTN = 0.6…

Q: What is the region of operation and drain current of an NMOS transistor having VTN = 1 V, Kn = 1…

A: Given: VTN = 1 V Kn = 1 mA/V2 The conditions of regions of operation are given by Conditions…

Q: +8V 多4.2K2 多5MA 2MA Ś Ro>?

A: First we will find drain current then we will find drain voltage in terms of Rd then we will find…

Q: --State the advantages of using power semiconductor switches in power electronics field --Show…

A: Nowadays, Power electronics switches are very popular due to their High power rating, high current…

Q: Calculate the transconductance for an NMOS transistor for VGS = 2 V and 3.3 V, with VDS = 3.3 V,if W…

A: Given data: VGS=2 VVDS=3.3 V Calculating VDS, VGS-VTN=2-0.7=1.3 V VDS>VGS-VTN Operating in…

Q: Design a bias network for a depletion-mode NMOS transistor to give a Q-point of (250 µA, 7.5 V) with…

A: Given data, VDD=15VVTN=-4VKn=1mA/V2ID=250μAVDS=7.5V

Q: b- Supported by drawing (structure, carrier movement, current flow, etc.), demonstrate BJT npn)…

A: In this mode, emitter to base junction gets forward biased and collector to base junction gets…

Q: 1. a) With the aid of a diagram, explain the working principle of a common-base NPN BJT transistor…

A: (a) Common-base NPN BJT transistor (A)NPN BJT Common Base TransistorIn a C-B configuration, the…

Q: Design a four resistor bias network and required transistor parameter for a NMOS transistor to give…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Q1. Determine a and ß for a BJT given an emitter current if 1.602 mA and base current being 16 µA.

A: In this question , we will find current gain ...

Q: en lEdc) = 2.1 mA, B= 110, and ro = 50 kOhms, sketch and write the corresponding values for the…

Q: The figure below shows NMOS and PMOS devices with drain, source, and gate ports annotated. Determine…

A: Part (c): NMOS: The condition for the saturation is given by: VDS≥VGS-VT0 Determine the value of the…

Q: XProblem No.5 (P5). A Common Base Configuration NPN BJT circuit is biased by a 10VDC supply (Vcc) at…

Q: An NMOS transistor has parameters Kn = 1.1 mA/V^2 , VTN = 0.5 V, VDS = 0.5 V, and VGS = 2.0 V. Is…

Q: 3.10 An NMOS device has parameters VrN =0.8 V, L =0.8 um, and = 120 uA/V. When the transistor is…

A: Kn = (Kn' /2)×W/L Use above relation to find channel width. N mosfet will oparate in non saturation…

Q: What is the region of operation of (a) an npn transistor with VBE = 0.75 V andVBC = −0.70 V? (b) A…

A: Given: VBE = 0.75 V VBC = −0.70 V VCB = 0.70 V VEB = 0.75 V

Q: A Bipolar Junction Transistor (BJT) is a device with three terminals consisting of either two n- and…

A: the characteristic curve of BJT showing its active operation, saturation as well as cut off regions…

Q: A p-channel enhancement MOSFET has Vto=−0.5 V and K=0.2 mA/V2. Assuming operation in the saturation…

Q: An npn transistor is operating with the base–emitter junction forward biased and the base–collector…

A: The circuit diagram for the given problem is given as

Q: For the circuit sown, using the transistor values of: ß = 200, lc = 4mA and lb = 20uA, find the…

A: The given circuit is a transistor based switching circuit. By using ohms law we can obtain the base…

Q: 3. From an old quiz. Regions of operation are very important in circuit design using MOSFETS.…

Q: Taking into consideration the Early effect in the npn transistor, we can state that the collector…

A: we need to know whether the given statement is true or false the statement is is :in early effect…

Q: 6. What is the effect of decreasing resistor Rg on Ico for the fixed- bias circuit? What is its…

A: BJT is a current controlled Device in which base current control the mode of operation of BJT. Mode…

Q: 0.5 mA 200 kn 20 kn 200 2

A: The solution is given below

Q: The figure below shows NMOS and PMOS devices with drain, source, and gate ports annotated. Determine…

A: Given The parameters of NMOS and PMOS are For NMOS, Kn'=115 μA/V2VTo=0.43 Vλ=0.06 V-1VDSAT=0.6 V For…

Q: For the circuit given below, suppose that RB = 230k2, RE1 = 4002, RE2 = 02, Rc = 1002 and VCC = +6V.…

Q: Consider an NMOS transistor operating in the triode region with VGs = 3V, Vtn = 0.7V, and kn = 2.5-…

A: (a)Given equation of incremental resistance rds=1∂iD∂VDSVDS=VDS (b)Given the values of…

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

An NPN BJT is biased in the forward active region. Assume that InE
1.000 mA, IpE = 0.005 mA,
Inc = 0.995 mA and Ipc 0. Calculate the emitter injection efficiency y, the base transport factor
B", the common emitter current gain Bdc, the common base current gain ade, respectively.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given Data

VIEW

Finding Emitter Injection Effeciency

VIEW

Finding Base Transport Factor

VIEW

Finding Common Emitter Current Gain

VIEW

Finding Common Base Current Gain

VIEW

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. a) With the aid of a diagram, explain the working principle of a common-base NPN BJT transistorin active mode and show the currents involved b) State reasons behind the design requirements of the base, emitter and collector of a BJT c) Calculate the α and β when the emitter current of BJT is equal to 1 mA and the collector currentis 0.995 mA
Suppose we have a certain pnp transistor that has VCE = −5 V, IC = 0.995 mA, and IE = 1.000 mA. Determine the values for α and β for this transistor.
What is the region of operation and drain current of an NMOS transistor having VTN = 1 V, Kn = 1 mA/V2, and λ = 0.02 V−1 for (a) VGS = 0 V, VDS = 1 V; (b) VGS = 2 V, VDS =0.5 V; (c) VGS = 2 V, VDS = 2 V?
The figure below shows NMOS and PMOS devices with drain, source, and gate ports annotated. Determine the mode of operation (saturation - velocity saturation or channel pinch-off, linear, or cutoff) and drain current ID for each of the biasing configurations given below, using the following transistor data. Assume (W/L) = 1 and VSB = 0.NMOS: k'n = 115µA/V2, VT0 = 0.43V, λ = 0.06V−1, VDSAT = 0.6VPMOS: k'p = −30µA/V2, VT0 = −0.4V, λ = −0.1V−1, VDSAT = −1.0V (a) NMOS: VGS = 2.5V , VDS = 2.5V . PMOS: VGS = −0.5V , VDS = −1.25V .
The figure below shows NMOS and PMOS devices with drain, source, and gate ports annotated. Determine the mode of operation (saturation - velocity saturation or channel pinch-off, linear, or cutoff) and drain current ID for each of the biasing configurations given below, using the following transistor data. Assume (W/L) = 1 and VSB = 0.NMOS: k'n = 115µA/V2, VT0 = 0.43V, λ = 0.06V−1, VDSAT = 0.6VPMOS: k'p = −30µA/V2, VT0 = −0.4V, λ = −0.1V−1, VDSAT = −1.0V (c) NMOS: VGS = 0.6V , VDS = 0.1V . PMOS: VGS = −2.5V , VDS = −0.7V .
Calculate the drain current for the NMOS transistor operating withVGS = 4 V and VDS = 5 V if VTN = 1 V, Kn = 25 μA/V2, and λ = 0.01 V−1. Repeat for VGS = 5 Vand VDS = 10 V.
Suppose that an npn transistor is operating with the base–emitter junction forward biased and the base–collector junction reverse biased. Given β = 200 and iB = 10 μA, determine the values of iC and iE.
(a) What is the base-emitter voltage in the circuitshown? Use the transport equations and thetransistor parameters from Table shown (b) What isthe base-emitter voltage if βF = 80? (c) What isVBE if IB is increased to 1 mA and βF = 40?
The output characteristics for a PMOS transistor. What are the values of Kp and VTP for this transistor? Is this an enhancement-modeor depletion-mode transistor? What is the value ofW/L for this device?
Q. What is the output resistance, rds, in kΩ for an NMOS FET operating in saturation with Id = 989μA ? Use: λ = 0.44 Give the solution !
An npn transistor is operating with the base–emitter junction forward biased and the base–collector junction reverse biased. Given iC=9 mA, for iB = 0.3 mA, compute iE, α and β.
4- What must be done for a voltage divider biased MOSFET in gate G to enter the cutoff region?5- What must be done for a voltage divider biased MOSFET in gate G to enter the linear/ ohmic region?6- Why are FETs preferred for low power applications?7- Write a difference between BJT and FET transistors.