An NTC thermistor is used to measure temperature. If temperature T₂ is greater than temperature T₁, then (a) resistance R₁ of the thermistor at temperature T₁is greater than resistance R₂ of the thermistor at temperature T₂ (b) resistance R₁ of the thermistor at temperature This smaller than resistance R₂ of thermistor at temperature T

An NTC thermistor is used to measure temperature. If temperature T₂ is greater than temperature T₁, then (a) resistance R₁ of the thermistor at temperature T₁is greater than resistance R₂ of the thermistor at temperature T₂ (b) resistance R₁ of the thermistor at temperature This smaller than resistance R₂ of thermistor at temperature T

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
7. A conducting wire has a cross-sectional area of 2 mm² and a specific resistance of 5x10 m. designed for a heater with a power of 1200 Watt, operating at different potential 220 V. Determine a. Required wire length (L.) b. Large current on the wire c. Electrical energy is transferred into thermal energy within 15 minutes d. What is the power of the stove if the length of the wire is half the length in problem a (1/2)
QUESTION TEXT A potentiometer consisting of a wire of length = 10 cm has a source of emf, ɛ = 15V connected across it. When a standard cell with emf V = 6V, in series with a voltmeter, is connected at one end of the wire and at a distance L along the wire the voltmeter circuit is in balance and the voltmeter reads zero. What is the value of the balance length L? Select one: a. 1.5 cm b. 4.0 cm c. 6.0 cm d. 2.0 cm
a) Explain the importance of thermal management of electronics devices. (b) Heat sink rated at 10°C/W will get 10°C hotter than the surrounding air when it dissipates 1 Watt of heat. Discuss the suitability of heat sink for above scenario in terms of thermal resistance. (c) Thermocouples are commonly used to measure temperature. There can be errors due to heat transfer by radiation. Consider a black thermocouple in a chamber with black walls Suppose the air is at 20 °C, the walls are at 100 °C, and the convective heat transfer coefficient is 15 Wm-2 k -1 . a) What temperature does the thermocouple read? b) If thermos couple sees a higher temperature than air, how could you reduce this error?
Choose the correct option. 1) Semiconductor materials havea) Positive temperature coefficientb) Negative temperature coefficientc) Unpolar temperature coefficientd) has both negative and positive coefficient but depends upon the conditions 2) The temperature coefficient is a a) Device temperatureb) Rise and fall of a temperaturec) Conductivity of a deviced) Rise and fall of conductivity with temperature 3) Electronic and Electrical devices area) Different in nature, principle, weight and power consumptionb) Electronics is a subfield of Electricalc) Works at different voltage levelsd) All of the above 4) Zener diode conducts ina) Forward regionb) Reverse regionc) Both forward and reverse regionsd) None of the above 5) Multisim is a simulation software that has a code for each electrical device it has.a) Trueb) False 6) A solar panel is also the application of a diodea) Trueb) False 7) Forward biasing causes current which is due to thea) minority carriesb) majority carriersc) Both…
Q21 A PMMC instrument gives 25 mA at full scale reading when a potential difference across its terminals is 32mV. Show that how it can be used (a) as an ammeter for the current measurement in the range of 0 –3 A (b) as a 0 – 510V range voltmeter for the voltage measurement. (c) find the multiplying factor of shunt and AND voltage amplification
A sample of wire (1 mm in diameter by 1 m in diameter) length) of an aluminum alloy (containing 1.2% Mn) is placed in an electrical circuit, as shown in the figure next to. A voltage drop of 432 mV is measured at wire length when it carries a 10 A current. Calculate the conductivity of this alloy.
Sketch and describe the construction of a moving-coilammeter and give the principle of operation.A moving-coil instrument gives full-scale deflection with 15 mA and has a resistance of 5 Ω. Calculatethe resistance of the necessary components in orderthat the instrument may be used as: (a) a 2 A ammeter;(b) a 100 V voltmeter
4. A coil of aluminum wire has a resistance of 50 when its temperature is 0°C. Determine its resistance at 100°C if the temperature coefficient of resistance of aluminum at 0°C is 0.0038/°C.
A heating element on an electric stove contains a wire that is 1.1 m long and has a cross-sectional area of 3.1 × 10−6 m2. This wire is contained in an electrically insulating casing surrounded by a metal casing. When electric current flows through the wire, it heats up, and subsequently the insulating and metal casings heat up as well. When the coil is at a temperature of 320 oC, the material the wire is composed of has a resistivity of 6.8 × 10−5 Ωm and a temperature coefficient of resistivity of 2.0 × 10−3 oC−1. (a) What is the resistance of the wire when it is at a temperature of 320 oC? (b) What is the resistance of the wire when it is at a temperature of 420 oC? (c) What is the resistance of the wire when it is at room temperature (25 oC)?
Consider the circuit below. Point b is grounded(potential=0). Determine the potential at a. Two resistors of cylindrical shape, A & B, made from the same material. The length of resistor A is twice that of resistor B. The diameter of B is half that of A. Determine the ratio of Resistance of A/Resistance of B.
a) With neat diagram, State the principle of RTD sensor b) A platinum resistance thermometer has a resistance of 100 ohm at 250C. The Resistance temperature coefficient of platinum is 0.00392 ohm/ohm0C. (i) Find its resistance at 500C (ii) Let the thermometer has a resistance of 200 ohm, calculate the value of temperature.