An op-amp has an open-loop gain A = 2,000 V/V, a non-inverting input voltage V+ = -5.5 V, and an inverting input voltage V_ = -5.505 V. Calculate the output voltage and include units in your answer. V_ +1

An op-amp has an open-loop gain A = 2,000 V/V, a non-inverting input voltage V+ = -5.5 V, and an inverting input voltage V_ = -5.505 V. Calculate the output voltage and include units in your answer. V_ +1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 8PP: In an R-L parallel circuit, ET=48 volts, IT=0.25 amps, R=320. Find XL.

See similar textbooks

Related questions

Q: Find vo by assuming op amps is ideal (X=3,Y=5)

A: Given: Brief description: By looking into the above given operational amplifier circuit it is very…

Q: The op amp in the circuit shown is ideal. Calculate vo.

A: Since op amp is ideal then voltages at point A and point B are same. VA=VB=2 V So the current in…

Q: 2. A741 op amp has an open-loop voltage gain of 2x10°, input resistance of 2 MQ, and output…

Q: 6. Find the output voltage, Vo assuming the op amp in the circuit below is ideal. 15k2 10k2 10k2 ()5…

Q: The resistor Rf in the circuit shown is adjusted until the ideal op amp saturates. Specify Rf in…

A: Given circuit is difference amplifier , here input is common mode input . Draw given circuit…

Q: Assume that the op amp in the circuit shown is ideal. How large can Rx be before the amplifier…

Q: 741 has an open-loop voltage gain of 2 x 10, input resistance of 2 Ml, and output op amp resistance…

A: Op amp

Q: Design an amplifier circuit using OPAMP with vo= (5*v1)+(v2)+(3*v3)-(2*v4). Draw vo knowing that v1…

A: Design an amplifier circuit using OPAMP with Output voltage vo= (5*v1)+(v2)+(3*v3)-(2*v4). Draw vo…

Q: In this problem, you will calculate the Thevenin equivalent resistance of an op-amp circuit as seen…

A: Part C: Put 1V test source at VC and deactivate all other independent source: From circuit the…

Q: 1. Find vo in the circuit shown if va=0.1 V and vb=0.25 V. 2. If vb=0.25 V, how large can va be…

A: Given data, The voltage va is 0.1 V The voltage vb is 0.25 V The resistance Rf is 250 KΩ The…

Q: For the single ended output differential amplifier perform (a) The DC analysis. (b) Determine the…

A: A differential amplifier can be single-ended output or double-ended output based on application.…

Q: Question 7 The op-amp in the amplifier circuit is ideal, except that its differential gain is not…

A: The gain is given as 85dB, evaluating the finite value of the gain:

Q: 7. Find the output voltage, Vo, in the circuit shown below assuming the op amp is ideal. Hint source…

Q: Find the output voltage vo in the given op amp circuit, where R= 35 kN. 50 k2 100 k2 100 k2 ww ww…

A: In this question, 3 op amplifier are connected as shown in the figure. Find the output voltage Vo…

Q: Consider the op amp circuit given below, where R = 19 kQ and vs = 1 V. NOTE: This is a multi-part…

A: The output voltage of the given circuit is determined as shown below

Q: Q2) Design an op-amp circuit which produce an output voltage as shown with input voltage Vin=…

A: The input for the circuit is a sinusoidal signal with amplitude 1. The input signal has both…

Q: b. Your high-fidelity amplifier has one output for a speaker whose resistance is 8 Q. How can you…

A: Given: A high-fidelity amplifier has: One output for a speaker whose resistance is 8 Ω. To find: How…

Q: Calculate vo in the op amp circuit. Given that vs = 6.2 V. 12 k2 +, + Vs (+ 20 k2 Vo The output…

A: The solution is given below

Q: 1. A3 stage amplifier has the following power gains and noise figures for each stage; Stage 1, power…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 5.3 Detemine the output voltage when-20 uV is applied to the inverting terminal of an op amp and +30…

A: Operational amplifiers

Q: Calculate the value of vo in the circuit at right. The op amps are ideal. R. 10 k2 4.7 k2 2.5 mA 10…

Q: 1.1 Find the relationship between V and V in circuits a and b of figure 1 assuming b) a) R R mmm…

A: The ideal op amp is a variation on the ideal amplifier concept. At all frequencies, a perfect…

Q: An op amp has a rated output voltage of +5 V and a slew rate of 1 V/us. What is its full-power…

A: Amplifier is an electronic device whose output is amplified version of the input signal. The…

Q: Find the output voltage vo in the given op amp circuit, where R= 30 kN. R 50 k 100 kΩ 100 k2 -ww vo…

Q: For the below given circuit, compute the following: (i) Open loop gains for all the op amps (ii)…

A: Op-amp

Q: Considering the Following Circuk with an ideal OP AMP. 1-Find vo whenvt-2v. va4v RI 2ko. R2 10ka. R…

A: Given: In the above given question we need to calculate the value of output voltage Vo. From the…

Q: Consider ideal OP Amps . Show your complete somtion 1 each probiem 330k 470k 33 K iam voW 41k Vo i 8…

A: In this question we will find output voltage...

Q: (i) Use a mathematical model to analyze the effect of Zout and Aol respectively. (ii) Use a 2-port…

A: Given the circuit: i) We need to use a mathematical model to analyse the effect of Zout and Aol…

Q: Solve

A: Redrawing the given circuit, by marking the inverting and the non-inverting terminal voltages as…

Q: If the input is given to the Pin number 2 of an Op Amp ,then it is known as Inverting Amplifier…

A: Pin diagram of opamp

Q: An op amp has a rated output voltage of ±10 V and a slew rate of 1 V/us. What is its full-powen…

A: Transistor ,OP-AMP are used as amplifier. Non inverting Amplifier: The output of non- inverting…

Q: 7. What is the difference between inverting and non-inverting Amplifier?

A: 1. In inverting amplifier, the feedback used is voltage shunt type and in non inverting amplifier,…

Q: The op amp in the circuit shown is ideal. Calculate vo if va=2 V and vb=1 V.

A: Given data: va=2 Vvb=1 V Apply KCL at inverting terminal, v--va20000+vb-vo100000+i1=0 Current i1 is…

Q: 2R 3R R V1( Vout V2 Consider the network above with V, = 6V, V, = 4V, and R = 2kQ. ne op-amp as…

A: Given

Q: Example:. Find A (cl)? 12. 10 5 2 A Op-amp w 7 TO V₂

A: In this question, We need to determine the Voltage gain of the op amplifier? We are solving this…

Q: Choose true or false with the explanation 1:-The gain of a summing amplifier must always be unity…

A: State whether the given statement is true or false

Q: The first stage of a 2 stage amplifier has a voltage gain of 10, a 600ohm input resistance, a 27Kohm…

A: The given information about 2 stage amplifiers is: The voltage gain for the first stage amplifier…

Q: 4. The transistor's output impedance (Zox) is: A. 42214.69 Q B. 955.93 Q 5. The amplifier's current…

Q: An op amp has a rated output voltage of ±10 V and a slew rate of I V/us. What is its full-power…

A: Given data : Rated Output Voltage =±10 VSlew Rate = 1V/μs

Q: erally ed to design a voltage amplifier? Justify your answer and m sible application. +V Ao

A: The operational amplifier is the differential amplifier. Which amplifies the difference in input…

Q: Using a series of source transformations to simply the circuit below with the current source Is1 = 5…

A: In this problem let us try to use the combination of source transformation technique and star to…

Q: Design a summing amplifier circuit that can be used to produce an output that ranges from –1 to – 5…

A: As we have given : Vin= 0 to 100 mVVout=-1 to -5 V

Q: Calculate the output voltage Vout for the ideal Op-Amp circuit shown below. Solution 470 2 $ 15 V…

Q: Design an amplifier circuit using OPAMP with vo= (5*v*1)+(v*2)+(3*v*3)-(2*v*4). Draw vo knowing…

A: The required design can be done simply by using two op-amp in cascade. The output waveform will be…

Q: Design a differential amplifier with a gain of 50

A: An differential amplifier is an subtraction amplifier which is used to get the difference of the…

Q: For the op amp circuit shown in the Figure, if Vs= 11 mV, R =10 KO, R1=8 KO and R2=4 KQ, the value…

A: We will apply KCL at opamp terminals to find output voltage. For ideal opamp voltage at inverting…

Q: An operational amplifier has a high input impedance and low output impedance. Do you think having…

A: Operational amplifier with high input impedance and low output impedance

Q: 3. For the amplifier circuit below, the op-amps are ideal. Calculate the output, vo, if the input is…

A: Given data, Input voltage is given, vi=0.2 V Circuit diagram is given as,

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

An op-amp has an open-loop gain A = 2,000 V/V, a non-inverting input voltage V+ = -5.5 V, and an inverting input voltage V_ = -5.505
V. Calculate the output voltage and include units in your answer.
V_
+1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Calculate the output voltage of an op-amp summing amplifier for the followingsets, consider Rf=1Mna. V1=+1v, V2=+2v, V3=+3v, Ri=R2, R3=500Ω b. V1=+1v, V2=+2v, V3=+3v, Ri-500kΩ, R2=1MΩ, R3=1MΩ
1. For the circuit shown, show that if ΔR<<R, the output voltage of the op amp is approximately vo≈Rf(R+Rf)R2(R+2Rf)(−ΔR)vin. 2. Find vo if Rf=470 kΩ, R=10 kΩ, ΔR=95 Ω, and vin=15 V. 3. Find the actual value of vo in (b).
For the circuit below, you may assume the op amps are ideal and V_Z = 5V. Use Ohm's Law, KCL, and/or KVL to determine values for R1,R2,R3,R4,and R5 such that V_out = 2.5V. Make surc your resistor values allow you to ignore the op amps' input resistances (1 M amps ) and output resistances (50amps).
subject: Communication Fundamentals Modulation and Demodulation (give solve sub-parts iv and v)
13- Amplifiers are used to increase the value of Resistance. Select one: True False
A three stage amplifier has the following gains and noise factor for each stage: 1st stage Gain=10 dB and Noise Factor = 2; 2nd stage Gain=16 dB and Noise Factor = 4; and 3rd stage Gain=20 dB and Noise Factor = 5. (a) Calculate the total noise figure. (3 points, Use 2 decimal places)
These are questions related operational amplifier. Please Solve all three sub-parts..Thank you
Figure Q. 3(b) shows an op amp circuit for linear amplifier application. (i) Determine the value of current I3.(ii) Find the value of R if the output current, Io is given as 2 mA.(iii) Explain what will happen to output voltages, V01 and V02 if the supplyvoltages, +VCC and -VCC are connected to +10V and -10V.
How to create a circuit that has three varying input voltages and one output voltage that is equal to the average of the three? Vin = V1, V2, V3Vout = (V1 + V2 + V3) / 3 Example:V1 = 750mV, V2 = 700mV, V3 = 800mVVo = 750mV You can only use resistors and OpAmps (operational amplifiers), show circuit schematic and computations/formulas used
Hi please calculate for the CMRR (measured) with resistor values: R1 = 995 Ohms R2 = 100.8 kOhms R3 = 1003 Ohms R4 = 99.7 kOhms Assume that the op amp itself has infinite CMRR. I will upvote thanks!
(a) An inverting amplifier with resistors R1=5.6 kQ and R2 = 120 kg is fabricated using an op amp with an open-loop gain of 105. What is the percent difference between the actual gain and the ideal gain? (b) Repeat part (a) if R1 is changed to R1 8.2 kA.
In the figure above, R_{a}Ra=1kΩ, R_{b}Rb=2kΩ, R_{c}Rc=3kΩ. R_{f}Rf=12kΩ. The sources are v_{a}va=−4V, v_{b}vb=+2V, and v_{c}vc=1V. The power supplies for the op-amp are +15V and −15V. What is the value of v_{o}vo? Notice that this op amp circuit might saturate, and you need to consider that possibility in your answer. Give your answer in volts and omit the units from your answer. What must be R_aRa be changed to so that v_{o}vo is 13 V? Give your answer in kilo-ohms with no units.