An open Brayton cycle using air operates with a maximum cycle temperature of 1300°F .The compressor pressure ratio is 6.0. Heat supplied in the combustion chamber is 200 Btu/lb. The ambient temperature before the compressor is 95°F, and the atmospheric pressure is 14.7 psia. Using constant specific heat, calculate the temperature of the air leaving the turbine, °F; A. 959 °F C. 837°F D. 647°F B. 595°F

An open Brayton cycle using air operates with a maximum cycle temperature of 1300°F .The compressor pressure ratio is 6.0. Heat supplied in the combustion chamber is 200 Btu/lb. The ambient temperature before the compressor is 95°F, and the atmospheric pressure is 14.7 psia. Using constant specific heat, calculate the temperature of the air leaving the turbine, °F; A. 959 °F C. 837°F D. 647°F B. 595°F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2250 K. Assume constant specific heats evaluated at 300 K. Determine the mean effective pressure, in kPa.
Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use Standard Cold Air Assumption Method (constant specific heats at room temperature, 25ºC).
The pressure and temperature at the beginning of compression of a cold air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 7.2 MPa and the temperature is 2050 K. Assume constant specific heats evaluated at 300 K.Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 100 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2050 K. Determine:(a) the compression ratio.(b) the cutoff ratio.(c) the percent thermal efficiency of the cycle.(d) the mean effective pressure, in kPa.
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa, 290 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (i)turbine work, (ii) compressor work, (iii) heat supplied, and (iv) the efficiency of the cycle. Draw a suitable block diagram and T-s diagram. Take Cp=1.005 kJ/kg K and ϒ= 1.4
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 100 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2050 K. Determine a. the compression ratio. b. the cutoff ratio. c. the thermal efficiency of the cycle. d. the mean effective pressure, in kPa.
Air enters the compressor of an ideal air-standard Brayton cycle at 88 kPa, 280 K, with a volumetric flow rate of 1225 m3/s. The compressor pressure ratio is 12. The turbine inlet temperature is 1225 K. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the thermal efficiency of the plant to one decimal place and include the correct unit (percentage). Use cold air standard assumption
The compression ratio of an air-standard Otto cycle is 7.5. P1 = 85 kPa and T1 = 32 Celsius at the startof compression. The highest temperature in the cycle is 960 K, and the mass of air is 3 g. determine the: (a) the heat rejection, in kJ, (b) the network, in kJ (c) the thermal efficiency, and the (d) mean effective pressure, in kPa. Show complete solution.
Air enters the compressor of an ideal air-standard Brayton cycle at 106 kPa, 281 K, with a volumetric flow rate of 1577 m3/s. The compressor pressure ratio is 13. The turbine inlet temperature is 1577 K. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the work ratio of the plant to one decimal place and include the correct unit (percentage). Us cold air standard assumption.
Air enters the compressor of an ideal air-standard Brayton cycle at 110 kPa, 289 K, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 12:1. The turbine inlet temperature is 1567 K. Take the gas constant as 289 J/kg.K and Specific heat at constant pressure and constant volume for air as 1.004 kJ/kg K and 0.708 kJ/kg K respectively. Calculate the net power developed to two decimal places and include the correct SI unit symbol.
The adiabatic efficiencies of the compressor and turbine used in an air-standard Brayton cycle are 85% and 90%, respectively. If the cycle operates between 14.7 and 55 psia and if the maximum and minimum temperatures are 1500 F and 80 F, respectively, compute the thermal efficiency of the cycle. Assume constant specific heats.
For an ideal cold air-standard Brayton cycle with a compressor inlet temperature of 300 K and a maximum cycle temperature of 1700 K, use Eq. in the picture to find the compressor pressure ratio that maximizes the net power output per unit mass flow. Assume k = 1.4