An orthogonal cutting operation is being carried out under the following conditions: depth of cut, to = 0.1 mm, chip thickness, to 0.2 mm, width of cut = 4 mm, cutting speed, v = 3 m/s, rake angle, a = 10°, Cutting force, Fo = 500 N, and Thrust force, Fi= 200 N. Calculate the percentage of the total energy that is dissipated in the shear plane of cutting process. %3!

An orthogonal cutting operation is being carried out under the following conditions: depth of cut, to = 0.1 mm, chip thickness, to 0.2 mm, width of cut = 4 mm, cutting speed, v = 3 m/s, rake angle, a = 10°, Cutting force, Fo = 500 N, and Thrust force, Fi= 200 N. Calculate the percentage of the total energy that is dissipated in the shear plane of cutting process. %3!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2 1.46 Explain why the power requirements in cutting depend on the cutting force but not the thrust force.
Discuss the effects of cutting speed, feed rate, and depth of cut on the tool wear rate during a turning operation. How does each parameter influence the surface finish of the workpiece? Provide a detailed explanation based on the principles of metal cutting mechanics.
An orthogonal cutting operation is being carried out under the following conditions: t0=0.38 mm, tc=0.65 mm, width of the cut= 2.5 mm, V=3.5 m/s, rake angle=6°, Fc= 515 N, and Ft=210 N. Calculate the percentage of the total energy that is dissipated in the shear plane.
In orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the main cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero Employing Merchant's theory, what is the ratio of friction force to normal force acting on the cutting tool?
In orthogonal turning of a bar 100 mm diameter with a feed of 0.25 mm/rev., depth of cut = 4 mm, cutting velocity = 90 m/min. it is observed that the main cutting force is perpendicular to friction force acting at the chip tool interface and cutting force is 1500 N. find (i) rake angle (ii) normal force.
21.61 In Example 21.3, if the cutting speed V is doubled, will the answer be different? Explain.
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
21.8 Why should we be interested in the magnitude of the thrust force in cutting?
a) It has been stated that it is generally undesirable to allow temperatures to riseexcessively in machining operations. Explain why?b) List out the cutting parameters which is influenced the rises of cuttingtemperature during turning process.c) Evaluate the relationship of these cutting parameters to the cutting temperaturewith graph.d) Propose the solution of how to reduce the temperature during the cuttingprocess.
What are the functions served by cutting fluid? Give broad classification of cutting fluid and explain each in detail .
Assuming that the coefficient of friction is 0.25, calculate the maximum depth of cut forturning a hard aluminium alloy on a 15-kW lathe (with a mechanical efficieny of 80%) at awidth of cut of 6 mm, rake angle of 0˚, and a cutting speed of 90 m/min, shear strength of 150 MPa.
An orthogonal cutting operation is being carried out in which to=0.2 mm, V=2m/s, a=7.5o, and the width of cut=5 mm. It is observed that tc=0.25mm, Fc=400N, and Ft=300N. Calculate the percentage of the total energy that is dissipated in friction at the tool-chip interface. A) 22% B) 50% C) 70% D)None of the above