An overhang beam carries a distributed load "w" and a concentrated load "P". If the maximum negative shear is -230.08333333333kN and the vertical reaction of hinge support is 209.91666666667KN, determine the following unknowns. (DRAW THE SHEAR AND MOMENT DIAGRAM) Let L1 = 4m and L2 = 1m L1 L2 Solve the value of "w": kN/m Solve the value of "P": kN Solve the reaction of the roller supp

An overhang beam carries a distributed load "w" and a concentrated load "P". If the maximum negative shear is -230.08333333333kN and the vertical reaction of hinge support is 209.91666666667KN, determine the following unknowns. (DRAW THE SHEAR AND MOMENT DIAGRAM) Let L1 = 4m and L2 = 1m L1 L2 Solve the value of "w": kN/m Solve the value of "P": kN Solve the reaction of the roller supp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the shear diagram of the line from B to C?A.15 KN/mB.16 KN/mC.24.46 KNmD.11.26 KNmThe change in moment [KNm] of the diagram above from point A to the concentrated load is nearest toA.98B.99C.100D.101
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
Find shear: VA VB VC VD Find Moment: MA MB MC MD Identify Shear Maximum & Moment Maximum
A short timber post of rectangular section has one side twice the other.It contracts by 0.05 cm/m. When loaded axially by 10kN, calculate thesections dimension of the post. When E= 0.1?10^5N/mm^2
The overhangingbeam shown supports two concentratedloads of 150 lbs. and 30 lbs.finda.Determine EI midway between thesupports.b.Determine EI at point B.
The tripod shown is to support a vertical load W and horizontal load P at point D. The legs of the tripod rest on a level rough surface at points A, B and C. If W=150N, P=50N, a = 0.5m, b =0.75m. c=1.125m, d=1.5m, 19. Determine the force acting on leg AD. Determine the force acting on leg BD.
The required stirrups spacing for a 10mm diameter ties in a reinforced oncrete bear with a depth of 800mm to carry the net shear of 83.8kN, if fy=200MPa is nearest to: a. 300mm b.120mm c.170mm d. 100mm
Determine the reactions at a and b for the beam subjected to the concentrated loads Ay= ? (Not 8.77 or 4.85 previous failed attempts on my behalf) bx = 7.2 Ax = ? (Not 1.9 or -.3365)
draw shear and moment diagrams w=1.5k/ft a= 10'-4.5'' b= 20'-9''
Steel Design Given: S = 2m L = 10m Superimposed dead load = 5 kPa Live load = 3.6 kPa Properties of Beam BFA section = W 460 x 97 kg/mArea (A) = 12320 mm^2Depth (d) = 465 mmFlange Width (bf) = 193 mmFlange Thickness (tf) = 19mmWeb Thickness (tw) = 11 mm Moment of InertiaIx = 445 x 10^6 mm^4Iy = 23 x 10^6 mm^4Yield Strength, Fy = 248 MPar (radius of gyration of a section compromising the compression flange plus 1/3 of the compression web area of compression flange = 50 mm. Consider bending about the x-axis. 1. The compression flanges are laterally supported only at midspan. With this condition, what is the permissible flexural stress if Cb = 1.0?
Draw the shear and moment diagrams given that Ra=110.2 kN, Rb=310.1 kN, Rc=220.6 kN, Ma=-124.5 kN m, Mb =-258.9 kN m, Mc = -160.5 kN
Solve fast please I need correct answes