An overhanging beam is roller-supported at point B and pin-supported at point D is loaded as shown in Figure Q5. Using an Integration Method and assume that El is constant, determine: the reactions at points B and D, (a) (b) the equation of the elastic curve, and (c) the deflection at point C.

An overhanging beam is roller-supported at point B and pin-supported at point D is loaded as shown in Figure Q5. Using an Integration Method and assume that El is constant, determine: the reactions at points B and D, (a) (b) the equation of the elastic curve, and (c) the deflection at point C.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.3.6P: A cantilever beam of a length L and loaded by a uniform load of intensity q has a fixed support at A...

See similar textbooks

Related questions

Q: 1. Consider the system with 7 = m(²+r²0² +2²) and U = mgz where z = cr².9= wt, by using the…

A: The Lagrangian method:

Q: 1. List the seven types of failure 2.Define die penetrant test 3.Suggest N.D.T.test for an internal…

A: 1.failure types : Yielding Fracture Elastic deformation Wear stress concentration crack…

Q: An oxygen cylinder has a capacity of 300 L and contains O₂ at 3.1 MPa and 18 °C. The value is open…

Q: The velocity of a flywheel whose diameter is 3 m. is increasing rom rest at uniform rate of 2…

Q: A composite wall is made up of 10 cm of common brick against 15cm of concrete with 1.5 cm of plaster…

Q: For the clevis connection shown, determine the shear stress in the 19-mm-diameter bolt for an…

Q: HW1 A uniform disc of 220 mm in diameter has a mass of 3.5 kg. It is mounted centrally in bearings…

Q: HW10 Two parallel shafts are to be connected by spur gearing. The approximate distance between the…

Q: The machine shown in the figure can be used for a tension test but not for a compression test. Why?…

A: Solution -

Q: The time of flight for any projectile is 20 sec and its horizontal range is 400m, what is its…

A: Given, Time of flight = tF = 20 s Horizontal range = R = 400 m In the projectile motion, the…

Q: A steady-state, steady flow adiabatic nozzle operates on air with these conditions. It has an inflow…

Q: In a piston subjected to a constant temperature T=125°C, there are 20 grams of water with a quality…

Q: Question 1 The 50-kg flowerpot is suspended as shown in Figure 1 from wires AB and BC which have…

Q: Calculate the heat (q) and the work (w) in Joules, which the system exchanges with the return…

Q: HW4 A ship has its turbine engine mounted with its axis of rotation lengthways in the ship. When…

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction: Given data: length of the upper arml1=300 mmlenght of the lower arml2=350 mmmass of…

Q: he sales forecast for the month of

A: Given data; An electric car manufacturer underestimated the, January sales of car=20 units Actual…

Q: HW9 In an engine governor of the Porter type, the upper and lower arms are 300 mm and 350 mm…

A: Introduction: Given data: upper arm lengthl1=300 mmlower arm lengthl2=350 mmmass of the center…

Q: For the beam shown; 1. Determine the equations of slope and deflection. 2. Determine the slope and…

Q: Determine the force in each member of the loaded truss. Explain why knowledge of the lengths of the…

Q: The elements of boundary model for box with through hole are OV= 10, E= 15, F= 9, H= 2, G= 1 and C=…

A: Write the given data from the given options. No. of vertices, V=10No. of Edges, E=15H=2No. of holes,…

Q: in made A screw clamp similar to the one shown in the figure has a handle with diameter in-14 UNC…

Q: A flywheel, starting from rest was able to rotate 23 times in 4.2 seconds. Solve for its angular…

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

Q: 3.) In In an actual Rankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to…

A: Given Data: Turbine-entry pressure, P3 = 10 MPa Turbine-entry temperature, T3 = 400 C Turbine-exit…

Q: The efficiency of a gas turbine is much larger than that of a steam turbine since Question 4…

A: given = multiple choice question

Q: نقطة واحدة 90,210 90,190 R70 90,90 * The correct choice to the bottom Arc with r (135) between p -…

A: Given data : Arc

Q: The telephone-cable reel rolls without slipping on the horizontal surface. If point A on the cable…

A: Given data as per the question vA=0.7 ms

Q: An aeroplane makes a complete half circle of 80 meters radius, towards the left, when flying at 400…

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

Q: Complete solution and units please. Use the sleam tables provided, and use 4 decimal places for…

A: Given: The turbine inlet pressure, P1 = 4 MPa The turbine inlet temperature, T1 = 300 C The…

Q: For the section shown, if the distance from the N.A to the steel centroid is 350 mm, 1 = 944.4 x…

A: The strain in steel : (926 × 10-6) .... (Option b)

Q: Glass has density of 3.1 Mg/ m³, specific heat of 0.88 j/g.k, fracture strength of 300 Mpa,elastic…

Q: Governor has all four arms 440 mm long. The upper arms are attached on the axis of rotation and the…

A: Calculated range of speed and sensitivity of Governors.

Q: Match the allowance and limit parameter in

A: Given data; Column given below; Column 1= Allowance and limit paramater Column 2=Quantitative…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: Wien's law is stated as follows: λmT = C, where C is 2898 um-K and Am is the wavelength at which the…

Q: 1. The heat absorption and rejection temperatures of a Carnot refrigeration cycle are -8°C and 36°C,…

A: The heat absorption temperature, TL=-8oC=-8+273=265 KThe heat rejection temperature,…

Q: A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are…

Q: Air moves at 0.85 of the speed of sound when it is 120°C and 1.2 atm. Air has a specific heat of…

Q: HW2 A uniform disc of 80 mm radius has a mass of 2000 g. It is mounted centrally in bearings that…

Q: Learning Goal: Consider the mass and pulley system shown. Mass m₁ = 32 kg and mass m2 = 10 kg. The…

Q: 05: For the given state of stresses shown, draw the required Mohr's circle and determine: The…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm².…

Q: An aeroplane makes a complete half circle of 80 meters radius, towards the left, when flying at 400…

Q: An element in plane stress from the fuselage of an airplane is subjected to compressive stresses of…

A: σy,1 = -18.5 MPa (Compressive)

Q: section. 12KN 20KN 10KN/m agti ட 2m 3m 5m 4m 3m B

Q: Q4/A/ The tension specimen contains has original length L. -100 mm as a result of the tension its…

A: Given:Lo=100 mmLf=120 mm

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: Solution - Given data - P= 385 N

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

An overhanging beam is roller-supported at point B and pin-supported at point D is loaded as
shown in Figure Q5. Using an Integration Method and assume that El is constant, determine:
(a) the reactions at points B and D,
(b)
the equation of the elastic curve, and
the deflection at point C.
(c)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported beam of a total length ll is shown in Figure Q5, where point A is supported by a pin connection and point C is supported by a roller support. The concentrated load is P=mgP=mg at the location of l1l1. Note that l1/l=l1/l= 0.65. Determine the shear-force and bending-moment distributions produced in the beam by the concentrated load PP.
Mechanics of solid A simply supported beam ABCD is subjected to a uniform distributed load along AB and CD as shown in Figure Q2. The properties of the beam are: E = 70 GPa and INA = 30x10^6 mm4. (a) Determine the deflection of the beam at point B. (b)Next, change the pin support at point A to a fixed support. Develop the slope and deflection functions.
1. A beam with the triangular cross section of Figure P4.7 is of length L and madeof material with Young’s modulus E. It is built in at one end and loaded by a force Fin the x-direction at the other end. Find the two components of displacement at theloaded end.
A wooden beam is loaded by a concentrated load P=1000N and supported by boundary conditions shown in figure Q5(a). The cross-section of the beam is shown in Q5(b). Given that LAB=1600mm,LBC=3400,B0=10mm,B1=20mm, and H=230 mm,h0=150mm,h1=40mm, determine the following quantities below
A wooden beam is loaded by a distributed load w = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1900 mm, LBC = 3100 mm, W=200 mm, B0 = 30 mm, and H = 200 mm, h0=20 mm. Units: use N, mm, MPa as consistent units for all calculations.
A steel beam is simply supported at both ends and laterally loaded to bend it plastically, as shown in Figure Q3a(i). The cross section is hollow, and the beam dimensions are illustrated in Figure Qa (ii). Find the value of load P, Shape Factor, and Length of Plastic Lp when the critical section is in fully plastic condition if the steel acts elastic-perfectly plastic with a Yield Stress of 200 MPa.
Rigid bar DB in Figure P5.7 is supported at pin B by axialmember ABC, which has a cross-sectional area A1 = A2 = 75 mm2,an elastic modulus E1 = E2 = 900 MPa, and lengths L1 = 400 mmand L2 = 600 mm. A load Q = 500 N is applied at end C of member(2), and a load P = 1,500 N is applied to the rigid bar at a distancea = 80 mm from pin support D and b = 50 mm from pin B. Determinethe downward deflections of(a) pin B.(b) pin C.
Can you please show me how to do this question; A steel beam, of lengths a = 5 m and b = 2 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 5.1 kN/m for AB span; and is constant with q = 5.1 kN/m for BC span. The Young’s modulus of steel is 200 GPa. Calculate: a) the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.
(VI.) In the following figure, a uniform beam of length 6.00 meters is supported by a horizontal cable and a hinge at angle 60.0 degrees, the weight of the beam and the box are 4.00x10^2 and 1.00x10^3 N respectively. Find out a) the tension in the cable, b) the forces the hinge exerts on the beam.
As shown in Figure Q3, a beam ABC is fixed at A and roller supported at C. The beam is used to support a uniform load, w = 5 kN/m along span AB and a couple, MB = 2 kN.m at B. C)Determine the slope and deflection at B in terms of EI.
A beam with a uniform load has a sliding support at one end and spring support at the other. The spring has a stiffness k = 48EI / L3. Derive the equation of the deflection curve by starting with the third-order differential equation (the shear-force equation). Also, determine the angle of rotation θB at support B.
modulus E of elasticity, for the ACB beam with inertia I;a) find the elastic curve equation by the singularity methodb) find the reaction force at point Ac) find the reaction force at Point B