An overhead transmission line conductor weighs 0.35 kg/m. Ultimate strength is 800 kg and factor of safety is 2.0. Span length is 160 m. One support is at a height 70 m from the ground. Determine the minimum clearance from the ground and the lowest point of the catenary from the supports if the second support is at a height (a) 40 m (b) 65 m from the ground.

An overhead transmission line conductor weighs 0.35 kg/m. Ultimate strength is 800 kg and factor of safety is 2.0. Span length is 160 m. One support is at a height 70 m from the ground. Determine the minimum clearance from the ground and the lowest point of the catenary from the supports if the second support is at a height (a) 40 m (b) 65 m from the ground.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.46P

See similar textbooks

Similar questions

Subject: Electrical & Electronics Engineering Course: Power Systems Question: What is GMR and GMD? Explain your answer in case of a composite conductor.
Besides the number of turns and the legth of active conductor, whit of the following is?are a factor which affects the amount of emf(voltage) induced in a coil? A) how fast the conductor is moving through the field(rate of incidence), B) the strength of the magtnetic field(flux density), C) the angle at which the conductor is cutting the magnetic field( angle of incidence), D) all of the above What is mean by genarator regulation? A) it is the percentage rise in terminal voltage from no-load to full-load, B) it is the percentage rise in terminal voltage full-load to no-load, C) it is the amount of control one has over the terminal voltage by way of the field excitation, D) none How are transformer components indetified? The algebraic symboly for the number of kilovolt-amperes on the load side of the transformer is_____. A) KVAh, B) KVAx, C) KVA-primary, D) KVA-secondary
A transmission line is supported from two towers at heights of 40 m and 58 m above ground level, the horizontal distance between the towers being 300 m. If the maximum allowable tension is 2500 kg, find the minimum clearance and the clearance at a point mid-way between the towers. Weight of conductor is 1 kg/m.
Describe the principles and benefits of High Voltage Direct Current (HVDC) transmission systems, and when are they preferred over traditional AC transmission systems?
7. Two towers of height 40 m and 30 m respectively support a transmission line conductor at water crossing. The horizontal distance between the towers is 300 m. If the tension in the conductor is 1590 kg, find the clearance of the conductor at a point mid-way between the supports. Weight of conductor is 0·8 kg/m. Bases of the towers can be considered to be at the water level.
An Overhead transmission line has a span of 115 m. Ultimate strength is 3600 Kg and factor of safety is 2. If the sag is 3 m, If the weight due to wind is 1.5 kg/m, Determine(a) weight of the conductor and(b) Length of the line
The diameter of the overhead lines in the form of cylindrical conductors in a 300 kV three-phase transmission system is 20 mm.a) - How much distance should there be between two conductors using the maximum area calculation equations?Calculate. (Puncture peak strength of air is 30kV / cm.)b) - In this configuration, if the distance between phase conductors is 0m, at what voltage levelCalculate the discharge occurs?c) - Maximum electric field in the same configuration, for electrode distances to be 0mCalculate the value. If needed in calculations Ꜫ0 = 8.854x10-12 F / m)
An overhead transmission line at a river crossing is supported from two towers at heights of 50 m and 100 m above the water level. The horizontal distance between the towers is 400 m. If the maximum allowable tension is 1800 kg and the conductor weighs 1 kg/m, Analyze the clearance between the conductor and water at a point mid-way between the supports.
A 84 meter long conductor with a unit weight of q=(0.8) kg/m is separated from each other.It is stretched on two poles in a straight span at a horizontal distance of "a" and the deflection valuef=16 meters measured. Accordingly, with the catenary method: a. Calculate the value of "a" b. Horizontal 18 meters from the lowest point of the conductor to any pole Calculate the deflection value at distance. c. Calculate the resultant tension force (S) at the peaks. D. At the apex, this is the angle that the direction of the S force makes with the horizontal axis calculate.
Propose a novel cable design that addresses specific performance or environmental requirements.
Which Transmission Line Parameter is neglected or ignored in most classifications of Transmission Line Equivalent Circuits? A. The Line Inductance B. The Line Resistance C. The Shunt Conductance D. The Shunt Capacitance
Use Maxwell's Method. Thank you