An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of +10 °C, compute the refrigerant flow rate in kg/s assuming that the clearance volumetric efficiency applies.

An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of +10 °C, compute the refrigerant flow rate in kg/s assuming that the clearance volumetric efficiency applies.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Related questions

Q: Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric…

Q: An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps…

Q: es 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves…

A: A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses…

Q: A water tube boiler has a heating Surface area of 500 m². For a developed boiler hp of 825.…

Q: Steam generators are a type of heat exchanges that are used in power plants to generate steam at…

Q: lbs -, ub = 0.044 erature of t; = 60°F and flows with an average velocity of 4 feet per s 13 ft? per…

Q: Q2. ( A steam generation unit in power plant operates at a constant pressure of (8 bar) and the…

A: Let the inlet denotes state 1 and outlet denotes state 2 Given, m˙=500 kg/h=5003600 kg/s=0.1388 kg/s…

Q: An ice plant produces 20 tons of ice per day at -15oC from water at 25 oC. If miscellaneous losses…

A: The amount of heat required to convert water at 250C to ice at -150C is to be calculated in tons of…

Q: SOLVE THE PROBLEM AND SHOW THE DETAILED SOLUTION A steam condenser receives 10 kg per second of…

A: To Find : The cooling water flow rate. Given : The mass flow rate is m˙s=10 kgs. The enthalpy of…

Q: A thermoelectric condenser is steamed at 20 kPa and 95 percent quality, with a 25,000 kg/h volcanic…

Q: Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber.…

A: Given: To find: make-up water and cooling water flow rates in kg/hr

Q: 2 m^3/min of a light oil are to be heated from 20C to 100C (with zero vaporization) in an exchanger…

Q: The food storage room requires a cooling system with a capacity of 10 tons of refrigeration which…

Q: Problem 2: Water flows in a horizontal pipe with an I.D. of 10cm (circular cross-section) and a…

A: Given data as per question

Q: A shell-and-tube condenser with horizontal 7/8-in BWG 16 copper tubes is used to condense benzene…

A: Tube diameter D0=78inch P=1 atm Enthalpy of vaporization hl =394 kJ/kg Thermal conductivity at…

Q: An industrial adiabatic heat exchanger utilizes cold-water stream to cool down the waste-hot air…

Q: An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps…

A: given R-22 working fluid C = 5%, Q = 80 L/s Tlow = -10o c , Thigh = 40o c

Q: Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of…

Q: Tomato juice flowing through a pipe at the rate of 100 kg/min is salted by adding saturated salt…

Q: Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of…

Q: Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber.…

Q: a supply tank having 14m long and 1.7m diameter is used to store fuel oil with 34degree API at…

Q: A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses…

Q: A 20% (by wt) sodium hydroxide solution is being concentrated to 50% (by weight) using an evaporator…

A: Given:- % of sodium: 20% temp of heating: 399k pressure: 13.3 kPa

Q: refrigeration in kW. The specif

Q: Steam generators are a type of heat exchanges that are used in power plants to generate steam at…

A: Given data Water enters at 30°C Diameter of tube = 60 mmVolume flow rate = 12 L/s = 12 x 10-3…

Q: 12.) Water at a rate of 1 lbm/s flows in a vertical heated tube (d = 1.5 in). System pressure is…

Q: Water at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a…

Q: 3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of…

A: Solution:

Q: Steam enters the condenser of a steam power plant at 30 kPa, a quality of 91% and a mass flow rate…

Q: (example question from slides) Steam enters the condenser of a steam power plant at 20 kPa and a…

Q: 15. A test tube for boiling water has a diameter of 25 mm. Water at a rate of 1000 kg/h enters the…

A: The enthalpy of steam during phase change a the given pressure and temperature can be calculated…

Q: he food storage room requires a cooling system with a capacity of 10 tons of refrigeration that…

Q: Sat. vapor at 250 kPa 1 Make-up water 20°C 5 4 25,000 kg/h 3 لیا Ejector nozzle Flash chamber water…

A: Please find the solution below

Q: In a reservoir system with a very large accumulation volume for the ideal fluid (water), a) Since…

Q: 1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet…

A: The Answer is below

Q: of 60 kW. The evaporating temperature is -5degC and condensing te

A: givenT1 =5°Cx1=1v1=vg=0.061 m3/kgk1=247 KJ/kgs1 =0.94 KJ/kg-kT2 = =35°cP2 =Psat@ 35°c=1610 KPaP2…

Q: A steam generation unit in power plant operates at a constant pressure of (10 bar) and the water…

Q: P.4.7 A heat exchanger is to consist of a number of tubes each 25 mm diameter and 5 m long arranged…

Q: A vacuum refrigeration system consists of a large insulated flash chamber kept at low pressure by…

Q: Two boilers are operating steadily on 91000 kg of coal contained in a bunker. One boiler is…

Q: The change of enthalpy in the condenser is 1500 KJ/kg. The temperature change of water is 16°C and…

A: given change of the enthalpy in the condenser ∆H=1500kJ/kgtemperature change of water…

Q: O.1.mirigid tank initially contains quality, The tunk is Connected by, a value iS Connected by.a…

A: P1= 1MPa , x1=100 %=1P2=1.2 Mpa; saturated liquid in pipe initially P=1.2 Mpa; T=30°Cat P1= 1Mpa ;…

Q: An ammonia compression refrigeration system is used to provide the cooling required for a…

Q: Brine enters a circulating brine cooler at the rate of 1000 Lpm. at -8°C and leaves at -18°C.…

Q: b) Steam generators are a type of heat exchanges that are used in power plants to generate steam at…

A: Water inlet condition= saturated liquid at 30oCTube diameter, d=60 mm =0.060 mVolume flow rate at…

Question

Please with proper solution. Thanks

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The evaporator design temperature may in some cases operate at a slightly ____(higher or lower) pressure and temperature on high-efficiency equipment because the evaporator is larger.
what is the developed boiler horsepower if the steam rate is 0.85 kg/s and the factor of evaporation is 1.25? thank you!
Water with a specific heat of 1 BTU/lbmoF is pumped using a 1-hp jet pump from a well that is 20 ft deep into a vented water vessel 160 ft above the ground. In the process, 400 BTU/min of heat is lost from the system. What is the temperature (oF) of the water as it enters the vessel if the flow rate of the water is 5 gal/min? Assume the temperature of water in the well is (35oF).
answer is provided and mass flow rate is 4.2 kg/sec
Water is provided at a rate of 0.1 L/s at 200°C from a faucet to the hose with nozzle. The hose is approximately 25 centimeters in diameter. When she turned on the power washer's motor, a jet of water with a velocity of 50 m/s ejected at a height of up to 5 m. Around 10% of the power input is transferred as heat from the motor to the surroundings. In kW, what is the power input? Assume a change in enthalpy of 12.54 kJ/kg for the water.
Benzene at 20 0C is pumped from one storage tank to a reactor (density=878 kg/ m3 ). Volumetric flow rate of benzene is 9.5x 10-4 m3 /s. The difference in the elevations of the two unit is 40m. The tank whichserves as a source is open to the atmosphere while the tank which receives the benzene has a pressure of P2 kPa abs in the vapor space above the benzene. 1‐in, schedule‐40 steel pipe and 2‐in Sch‐40 steel pipe isused in suction and discharge line respectively. Total friction loss of the system given as 135 J/kg . Pressure gauges in the pipeline at the inlet and outlet of the pump read (P3) 34.5kPa and (P4) 1051.6kPa, respectively. Efficiency of pump is %75 a) Calculate the power of pump (kW). (Fluid Mechanics Question) (Please answer it detailed and step by step)
The stream of air and gasoline vapour,in the ratio of 14:1 by mass, enters a gasoline engine at a temperature of 30C and leaves as combustion products at a temperature of 790C. The engine has a specific fuel consumption of 0.3kg/kWh.The net heat transfer rate from the fuel-air stream to the jacket cooling water and to the surroundings is 35kW.The shaft power delivered by the engine is 26kW.Compute the increase in specific enthalpy of the fuel-air stream, assuming the changes in kinetic and potential energy to be negligible.
A 15-ton refrigeration system is used to make ice. The water is available at 20°C. Refrigerant12 is used with saturated temperature limits of -25°C and 54°C. Determine (a) the COP, (b) therefrigerant flow rate, (c) the temperature at discharge of the compressor, (d) the volume flowrate, and (e) the maximum kg of ice manufactured per day.
Ammonia and air pass through the heat exchanger. While the ammonia is entering as asuperheated vapor at 16 bar pressure and 60C temperature it is leaving as a saturated liquid at thesame pressure but unknown temperature. The ammonia mass flow rate is 400 kg/hour.Air is flowing backward and is heated from 17C to 42C at the constant pressure of 2 bars.NOTE: Find air properties from https://www.peacesoftware.de/einigewerte/luft_e.html a. Draw the ammonia T-v diagram showing the stages, pressures, and temperatures b. How much heat is transferred from ammonia to air assuming no heat transfer to thesurroundings? c.Determine air mass flow rate Please show all steps in solution thanks
In a reservoir system with a very large accumulation volume for the ideal fluid (water),a) Since the diameter of the ABCDEF outlet pipe is D = 20 cm, the flow rate through the pipe,b) Calculate the velocity, velocity height, relative pressure and pressure heights in the ABCDEF outlet pipe.c) Draw the relative energy and piezometer lines of the system.d) If the relative evaporation pressure of water is pv = -98.5 kPa, what can be z maximum?e) Determine how much the diameter of the outlet pipe can be reduced at most without causing cavitation, with the relative evaporation pressure of water pv = -98.5 Pa and h = 6 m.f) Calculate the critical velocity value for cavitation.
What is mass flow rate of a liquid flowing through a pipe? Derive Bernoulli’s equation.
Prove this equation for the frictional adiabatic process in a fixed cross-section duct.