Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:

Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.29P

See similar textbooks

Similar questions

Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.51 m and is kept at 111 deg C. What is the power required to boil the water? Tsat = 100°C; Properties of water at 100°C: Density, ρl= 961 kg/m3; Kinematic viscosity, ν = 0.293x10-6 m2/s; Prandtl Number, Pr = 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, μ = ρ × ν = 961 × 0.293 × 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 kJ/kg; ρv = 0.597 kg/m3; σ = 0.0588 N/m; Csf=0.013; n=1; Select one: a. 25964.0356 b. 52997.1101 c. 49373.4011 d. 38911.7986
The critical temperature of gas TOS is -46 deg Celsius. If the value of its Van der Waals constant b is 2.1 x 10 -5 m3/n, find the value of its VDW constant a in Pa-m6/n2
(About measuring specific heat capacity) Since metal sample can be heated to any desired temperature value, say, 65°C or 156°C. Why is it practical to set the initial temperature of the metal sample near the boiling point of water? In connection to this, why should the dipper be partly submerged in the water while heating the metal sample?
Scale and sludge formation causes serious problems in boilers. Explain how the scalesand sludge are formed in the boilers and the problems caused by them. How can theseproblems be avoided?
6. A vertica platc 450 mm high and maintained at 3°C is exposed o satuated seam atatmospheric pressare. Calculte: (1) The rate of hea ransfe, and () The condensate a per hour per mete for plae widih film condensation. “The propertiesof waer im at the mean temperaure are: 0.3 kg/m sk = 6.4 x 10 WinC; = 434 x 10° kg/ms; and b = 22569 kg [Ans. 4399 x 10° kI, 2188 ke/h]
In a reservoir system with a very large accumulation volume for the ideal fluid (water),a) Since the diameter of the ABCDEF outlet pipe is D = 20 cm, the flow rate through the pipe,b) Calculate the velocity, velocity height, relative pressure and pressure heights in the ABCDEF outlet pipe.c) Draw the relative energy and piezometer lines of the system.d) If the relative evaporation pressure of water is pv = -98.5 kPa, what can be z maximum?e) Determine how much the diameter of the outlet pipe can be reduced at most without causing cavitation, with the relative evaporation pressure of water pv = -98.5 Pa and h = 6 m.f) Calculate the critical velocity value for cavitation.
What are the Poisson equations? How would the respective equations look like at isothermal, iso-choric, isobaric conditions?
Only answer if you are 100% sure otherwise i will downvote... An ASTM B75 copper tube sheathes a heating element that is used to boil water at 1254 kPa. The copper tube is immersed horizontally in the water, and its surface is polished. The tube diameter and length are 5 mm and 9.5 cm, respectively. The maximum use temperature for ASTM B75 copper tube is 204°C. Determine the highest evaporation rate of water that can be achieved by the heater without heating the tube surface above the maximum use temperature. Use the property tables to calculate the properties of water at saturation temperature. The surface tension 0 at 190°C is 0.03995 N/m. Also, Csf 0.0130 and 10 for the boiling water on a polished copper surface. The highest evaporation rate of water is g/s?
What is boiling and when does occurs? Explain pool boiling. How does it differ from forced convection boiling?
At 30ᵒC (ρ = 996kg/m3 and σ = 0.0712N/m) what diameter glass tube is necessary to keep the capillary-height change of water less than 2mm?
What is the temparature at depth 1 cm from the surface at t=2 minutes after the start of the coolıng ?
Saturated steam at 1 atm condenses on a 3-m-high and 5-m-wide vertical plate that is maintained at 90 0C by circulating cooling water through the other side. Determined (a) the rate of heat transfer by condensation to the plate, and (b) the rate at which the condensate drips off the plate at the bottom (Please use the condensation formulations at the Geankoplis).