Answer letter B A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. A. What is the total losses? a. 2512 W b. 1756 W c. 3718 W d. 3042 W B. What is are the rotational losses? a. 1125 W b. 1667 W c. 917 W d. 825 W

Answer letter B A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. A. What is the total losses? a. 2512 W b. 1756 W c. 3718 W d. 3042 W B. What is are the rotational losses? a. 1125 W b. 1667 W c. 917 W d. 825 W

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 19RQ: A motor is operating a load that requires a torque of 750 lb-in. and is turning at a speed of 1575...

See similar textbooks

Related questions

Q: The ohmic value of impedance to be connected in the neutral to ground circuit of a 2000 kVA…

Q: At t = 0, a charged capacitor with capacitance C = 500μF is connected in series to an inductor with…

A: Given data, Capacitor is given C=500 μF. Inductance L=200 mH. Rate of change of current didt=20 A/s.

Q: gh-voltage direct-current generating station delivers 5 MW of power at 178 kV to a city, as depicted…

A: In this question We need to determine the power across the transmission line. We know Power P= VI =…

Q: In the circuit given below, R = 20 2. Using nodal analysis, find vo and io in the given circuit. 96V…

A: I have written this solution as handwritten solution. Hope you find your solution clearly.

Q: determine the current through the voltage across and the power dissipated by each resistor.

Q: 10v (2) BI 2,245 VA R3 3.9k P24.7km VB lkn h4

A: here we have to find the node voltages VA , VB

Q: An alternator is supplying a load of 300 kW at 0.6 p.f. lagging. If the power factor is raised to…

Q: what is the minimum size single conductor of copper jacketed mineral insulated cable that can for a…

A: To find what is the minimum size single conductor of copper jacketed mineral insulated cable that…

Q: Explain the function of modern adaptive front lighting systems. In your answer, provide an example…

A: To explain: The function of modern adaptive front lighting systems.

Q: Identify the correct equation for the supernode in the circuit below. 20V 10V 252 V₁ 252 + V₂ www…

Q: A unity feedback system has the following G(s) 2 G(s) = 8+3 Use the LaPlace Transform to calculate…

A: Given , A unity feedback system has, Forward path transfer function, Gs=2s+3. Feedback transfer…

Q: What does boundary conditions mean in a transmission line?

A: Boundary conditions in a transmission line refer to the conditions at the ends of the line that…

Q: You want to design Geo Stationary s-band (2 GHz) antenna. If 2 beam is required for an aperture,…

A: Here, The Requirement is to design Geo Stationary S-band antenna of 2GHz. So,…

Q: What is the power factor angle? a. -12 degrees b. 45 degrees c. -30 degrees d. -18 degrees

A: It is given that: p=4Pop=75 kWf=50 HzVl=440 V%η=95%Xs=2.5 ΩPin=78950 W

Q: An inductor is formed by 10 turns of a thin conducting wire into a rectangular loop centered at the…

A: Question is related to voltage induced due to B varying as a function of both space (x) and time (t)…

Q: INDUCTION MACHINES PROBLEMS P1. Determine the number of poles, the slip, and the frequency of the…

A: The question is from induction machines. Here multiple questions are there and question 8 is not…

Q: Given the NE555 timer IC and a 9 V supply, design a circuit to generate a continuously running…

A: NE555 Timer IC:

Q: This should be a structural code. Can you write a sturctural Verilog code for the image given?

Q: Derive the drain current equation for PMOS transistor at non-saturation region and saturation…

A: according to the question, we need to derive the drain current equation for PMOS transistor at…

Q: e capacitor combination in the figure below is charged to an initial voltage of AV between points a…

Q: 50 µF 70 μF 60 μF 20 µF " 120 μF Respuesta: 40 μF.

Q: determine complex Fourier Series f(1) T 2 A -A Even function T 4 T 2

A: Given: A periodic function, To find: Complex Fourier series.

Q: A particular wind turbine generator outputs 1500W of AC power at its peak performance. If the…

A: Given Efficiency = 95%, Power output = 1500 watt To determine Power Consumed

Q: Given vectors A = ca, + a, + 4a₂ B = 3a, + Ba, - 6a, C = 5a. − 2a, + yaş determine a, B, and y such…

Q: XP1 Perform the operation (5 - 14)10, or (5+ [-14])10, using 5-bit two's complement addition. In…

Q: The approximate equivalent resistance between terminals A and B for the following infinite ladder…

A: Given, Infinite ladder network,

Q: A current of (120-j150) A flows through a circuit when applied voltage is (8 + j12) V. A. What is…

Q: A PIC18F6393 is connected to a push button SW and an LED DI, as shown in Figure 1. Write an…

A: Given: A PIC18F6393 is connected to a push button SW and an LED DI. To find: An instruction sequence…

Q: 10 Ω + 30 Ω Μ ἐγ + 10 Ω Μα 6Ω Μ I +

A: We need to find out the voltage across current source for given circuit .

Q: 3 Single Phase, 100 kVA transformer are connected delat to supply an assorted load of 160 kW at 0.8…

A: 3 phase transformer:

Q: 2] Now, let's consider what happens when things get away from ideal a bit. Let's repeat the divider…

A: It is given that:

Q: Based on DC circuit in Figure Q.1(a): i. Draw the Thevenin equivalent circuit as seen from terminal…

Q: The solution looks incorrect. For node voltage 3 analysis it should be in respect to node 3 not node…

Q: 2.1 Find the number of equipotential common tie-points in Fig. 2-23: Fig. 2-23 + > 1 www ww ww www…

Q: PROBLEMS 3. Find i for t> 0 if i(0) = 4 A. 8 A 6 Ohm 2 Ohm 1 H

A: In this question we need to find the current I shown in the given circuit for t>0

Q: Calculate the inductance of the coaxial cable (Inductance per unit length) when the outer diameter…

A: Note: b= outer diametera=inner diameterL=μ02πlnba H/m

Q: From the circuit shown, find the total resistance at terminal CD

A: In this question we need to find the total resistance of the given circuit at terminal CD.

Q: Attach a 10 V load to the terminals and find the voltage and current across each resistor in the…

Q: Obtain the Laplace transform of the signal u(t)

Q: Solve for v(t) in the following integro-differential equation using the phasor method and write the…

A: dv(t)dt+50v(t)+100∫v(t)dt=432cos(46t+34°) Introduction: Phasor method: A phasor method is a…

Q: A stringed instrument generates a complex waveform with the following components: 250 Hz with an…

A: I have written this solution as handwritten solution. Hope you find your solution clearly.

Q: decimal praces 1. A 250V, 4 pole, wave wound DC series motor has armature and series field…

Q: A moving coil instrument gives full deflection with 15 mA. The instrument has resistance of 5 ohms.…

Q: 5 (s+3)(s+6) 3. For each of the transfer functions shown below: (a) plot the locations of the poles…

Q: • What is the period of the following sinusoidal voltage signal v(t) = 229 cos (296t + 440 ) V?

Q: Choose the function that describes the logic circuit presented. C B F

A: Given data, Circuit diagram is given as,

Q: When the charge in this circuit discharges, why does the charge on the capacitor have to go through…

A: In this question We need to explain why does the charge on the capacitor have to go through R2 only…

Q: Question No.2 Two capacitors of 2 µF and 4 μF are connected in parallel across a 100-V DC supply.…

A: Given data, Two capacitors are connected in parallel, C1=2 μFC2=4 μF Across supply voltage, Vs=100…

Q: 1.9 Calculate the rate of attenuation increase in dB/ octave and in dB/decade as f approaches zero…

A: Given Transfer function is T(s) = [3s2(s2+36)] / [ s4+2.344s3+ 1.824s2+1.267s+0.987] We need to find…

Q: 1. What is the function of the modulator? 2. What are the signals called? input and output of the…

A: To explain: 1. Function of the modulator. 2. Input and output of the modulator. 3. Function of the…

Concept explainers

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.

Question

100%

Answer letter B

A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm.

A. What is the total losses?

a. 2512 W

b. 1756 W

c. 3718 W

d. 3042 W

B. What is are the rotational losses?

a. 1125 W

b. 1667 W

c. 917 W

d. 825 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. A. What is the total losses? a. 2512 W b. 1756 W c. 3718 W d. 3042 W B. What is are the rotational losses? a. 1125 W b. 1667 W c. 917 W d. 825 W
A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. What is are the rotational losses? a. 1125 W b. 1667 W c. 917 W d. 825 W
A 220v shunt generator has an armature resistance of 0.02 ohm and a shunt resistance of 44 ohms. At rated load, the driving engine develops 62.25 hp. If the iron and friction losses amount to 1600w. What is the electrical efficiency?
A dc series motor drives a load a 30rev/s and takes a current of 10A when the supply voltage is 400V. If the total resistance of the motor is 2Ω and the iron, friction and windage losses amount to 300W , determine the efficiency of the motor ANSWER:_______________%
10.a. An auxiliary motor is driving a synchronous alternator to determine its efficiency. When the test is madewithout field excitation, the data sheet shows the motor input to be 65 kw and the motor losses to be 30kw. The friction and windage losses of the alternator areA. 30 kw.B. 35 kw.C. 65 kw.D. 95 kw.10.b. In a d-c machine, which one of the following losses is a no-load loss?A. Ventilating lossB. Stray-load lossC. I²R lossD. Core loss
A series motor, working on 500 V d.c. supply, runs at a speed of 1000 r.p.m when load current is 120 A. Resistance of motor is .15 ohms of which 0.04 ohms is the resistance of field. Assuming an unsaturated field, calculate the speed of motor when the torque is ½ of the full load torque and the field winding is connected in parallel with diverter resistance of 0.08 ohm.
20. A 25 kW, 250 V dc shunt generator has armature and field resistance of 0.06 ohm and 100 ohms respectively. Determine the total armature power developed when working as a motor taking 25 kW input.
8.) A 25-kW shunt generator is delivering full output to 400-V bus-bars and is driven at 950 r.p.m. by belt drive. The belt breaks suddenly but the machine continues to run as a motor taking 25 kW from the busbars. At what speed does it run ? Take armature resistance including brush contact resistance as 0.5 Ω and field resistance as 160 Ω.
Three-phase asynchronous motor with a nominal value of 20 kW, 6 poles. It has a voltage value of 420 volts in a 50 Hz network. At 950 rpm, it draws 50 Ampere current from the network. Since the iron and friction losses total 1000 watts, calculate the total copper losses and the shaft torque? A) 1107 watts, 203 Nm B) 1105 watts, 201Nm C) 1108 watts, 204 Nm D) 1106 watts, 202 Nm
ANSWER THE PROBLEM, ILLUSTRATE THE CIRCUIT AND ANSWERS MUST BE IN 2 DECIMAL PLACES. A long shunt generator running at 1000 RPM supplies 20 kW at a terminal voltage of 220 V. The resistance of armature, shunt field, and series field are 0.04, 110 and 0.05 ohm respectively. The overall efficiency at the above load is 85%. Find: the total Copper loss, SPL, and the torque developed by the prime mover.
29. a) A Series motor takes a current of 20 A when the supply voltage is 230V. If the total resistance of the motor is 2 Ω and the Iron, Friction, Windage losses are 100 W. Find the efficiency of the motor. b) In DC motor, Back emf is less than Supply voltage. Justify
Problem: A shunt generator delivers 1,000 W at 142 V to a load. If the armature resistance is 0 Ω, and the shunt field resistance is 73 Ω, calculate the shunt field current in ampere (up to four decimal places).