Answer the following problems using the specified method up to four (4) iterations only. Round offany computed value to four (4) decimal places.9. Use Fixed-Point Iteration Method to locate the root off(x) = sin(√x) - xUse an initial guess of x = 0.5.Answer: 0.7621

Answered: Image /qna-images/answer/965bde85-08d9-48c5-9cc7-a76e8efef723.jpg

Answered: Answer the following problems using the…

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter16: Table Of Decimal Equivalents And Combined Operations Of Decimal Fractions

Section: Chapter Questions

Problem 32A

See similar textbooks

Similar questions

Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Cast iron, 312 inches in diameter, is turned in a lathe at 270 rpm. Each length of cut is inches and five cuts are required. A carbide tool is fed into the work at 0.015 inch per revolution. What is the total cutting time?
Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. An annealed cast iron housing is drilled with a cutting speed of 20 meters per minute using a 22-millimeter diameter carbon steel drill. Find the revolutions per minute.
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Fifteen 3.20-millimeter diameter holes each 57.15 millimeters deep are drilled inan aluminum workpiece. The high-speed steel drill runs at 9200 r/min with a feedof 0.05 millimeter per revolution. Determine the total cutting time.
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Seven brass plates 9.00 inches wide and 21.00 inches long are machined with amilling cutter along the length of the plates. The entire top face of each plate ismilled. The width of each cut allowing for overlap is 212 inches. Using a feed of0.020 inch per revolution and 525 rpm, determine the total cutting time.
Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. Determine the revolutions per minute of an aluminum alloy rod 1.250 inches in diameter with a cutting speed of 550 feet per minute.
Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. A high-speed steel milling cutter with a 1.750-inch diameter and a cutting speed of 40 feet per minute is used for a roughing operation on an annealed chromium-nickel steel workpiece. Find the revolutions per minute.
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. A finishing cut is taken on a brass workpiece using a 100-millimeter diameter carbon steel milling cutter. What is the cutting speed when the cutter is run at 86 r/min?
Answer the following within 10-5. Using the method that used in the images. 1. Use Fixed-point iteration method to solve sin x - e-x = 0, [0, 1].
Answer the following within 10-5. 1. Use Fixed-point iteration method to solve sin x - e-x = 0, [0, 1]. 2. Use Newton-Raphson method to solve x - cos x = 0, [0, π/2].
NEED ASAP!! Find a root greater than zero of f(x)=e^x−2x−5 using the Fixed-Point Iteration Method with an initial estimate of 2, and accurate to five decimal places.
. Find the root of x3−2x +14=0, correct to 3 decimal places using the Newton-Raphson method.

Recommended textbooks for you

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Linear Algebra: A Modern Introduction

Algebra

ISBN:

9781285463247

Author:

David Poole

Publisher:

Cengage Learning

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Linear Algebra: A Modern Introduction

Algebra

ISBN:

9781285463247

Author:

David Poole

Publisher:

Cengage Learning

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

SEE MORE TEXTBOOKS

Answer the following problems using the specified method up to four (4) iterations only. Round off any computed value to four (4) decimal places. 9. Use Fixed-Point Iteration Method to locate the root of f(x) = sin(√x) - x Use an initial guess of x = 0.5. Answer: 0.7621