Answer the following questions given the timing diagram of a certain flip-flop which has a clock of 10 MHz and a propagation delay time of 28 ns. CLK A B OUT After the circuit's triggering portion of the clock, how long does it take for the output, OUT, to change state? а. 1 us c. 28 ns b. 0.1 us d. 128ns

Answer the following questions given the timing diagram of a certain flip-flop which has a clock of 10 MHz and a propagation delay time of 28 ns. CLK A B OUT After the circuit's triggering portion of the clock, how long does it take for the output, OUT, to change state? а. 1 us c. 28 ns b. 0.1 us d. 128ns

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which of the following is/are true about RS flip-flop? a. It outputs Logic 1 b. It outputs Logic 0 c. It copies the previous Q d. a & b e. a, b & c f. None of theabove
Design a 5 asynchronous counter counting from 7 to 2. (JK or T type flip-flopsuse)
Draw the circuit, and show the truth table, for the clocked Master-Slave JK ﬂip-ﬂop
Analyze the timing diagram. Which flip-flop is being used? CLK PRE CLR J,K Q 1 0 1 0 1 0 a b e It is negative clock pulse
Micriprocessor Systems Question: A 4 ns mark & 6 ns space clock is passed via an inverter to a JK-type flip-flop whose two inputs are connected to the power supply. Compute the frequency and duty cycle of the input CK & the output Q of the flip-flip
a. ABCD=1010, Write the value of the shift register after applying three clock pulse. (D-flip flop)b. Complete the following timing diagram for a T flip-flop. Assume no gate delay
Suppose that Q1 = 1 and Q2 = 0 is the initial state of the two JK flip-flop circuit shown. What is the state of the circuit after applying two complete clock pulses? Draw the complete timing diagram .
Illustrate a complete timing diagram (i.e., one entire cycle back to the starting states) for a 4 bit ripple counter created using T flip-flops with negative edge clock triggers.
For the path in the following figure, determine which latches borrow time and if any setup time violations occur. Do this for a cycle time of 1000 ps and a duty cycle of 50%. Assume for the latches and flip-flops the setup and delay time is 100 ps. Use Δ1 = 250 ps , Δ2 = 600 ps, Δ3 = 600 ps. Will the circuit function correctly with the given combinational circuit delays? Explain.
Design synchronous counter(s) that go through each of the followingsequence(s) f. 1 3 5 7 6 4 2 0 and repeat usingi. JK flip flops Show a state diagram, indicating what happens if it initially is inone of the unused states for each of the designs.
Use T flip flops to design a counter with the repeated binary sequence: 0,1,3,5,7. The circuit is to be designed by treating the unused states as don’t care conditions. 1. Sketch the state diagram 2. Derive the state table 3. Implement the circuit.
Assume a three-story hospital is built at Expo Center Karachi, and you are hired to design the logic circuit for the newly installed lift. The lift only stops at Ground, Second, Third Floors. The lift has one button (RUN), that can be turned into Up or Down position. When the switch is turned to the UP position (i.e. R=1), the lift goes upward from the Ground floor (i.e. 0) to the top floor (i.e. 3), and if the switch is turned to the DOWN position (i.e. R=0) it will go downward. Design this synchronous sequential circuit for this up-down counter using the JK-flip- flops. Perform all design steps, including state-diagram, state-table, K-map, minimized expressions and finally, the draw the logic circuit.