A register is two or more D Flip-flops connected to the same clock (enable) input. A shift register is an n-bit register that shifts its stored data by one bit position for each cycle of the clock. Shift registers can be used to perform multiplication, division, and serial-to-parallel conversion, among many other tasks. Show how to wire up a 4-bit shift register using D flip-flops.

A register is two or more D Flip-flops connected to the same clock (enable) input. A shift register is an n-bit register that shifts its stored data by one bit position for each cycle of the clock. Shift registers can be used to perform multiplication, division, and serial-to-parallel conversion, among many other tasks. Show how to wire up a 4-bit shift register using D flip-flops.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a 4-bit shifter with four d flip flops and 2 to 1 multiplexers which can implement left shift and right shift operations according to the control signal c. Draw the logic diagram. C=1 left shift and c=0 right shift
You are asked to construct a multi-function shift register with the functionality shown**: Design a one bit circuit which implements the functionality. Use D flip flops and any logic gate and/or combinatorial circuit seen in class. Label all inputs and outputs.
Design a 4-bit arithmetic circuit, with two selection variables S1 and S0, that generates the arithmetic operations in the following table. Draw the logic diagram for a single bit stage. Note that B’ represents “Not B”. Draw the logic diagram for a single bit stag
You are asked to construct a multi-function shift register with the functionality shown**: A. Design a one bit circuit which implements the functionality. Use D flip flops and any logic gate and/or combinatorial circuit seen in class. Label all inputs and outputs. B. Use the one-bit circuit from (A) to implement a four bit shift register. Use the principal of abstraction to represent each instance of the circuit from (A) as a functional block. Clearly label all ports.
Course: Computer Engineering Subject: Logic Circuit and Switch Theory Find a function to detect an error in the representation of a decimal digit in BCD. In other words, write an equation with value 1 when the inputs are any one of the six unused bit combinations in the BCD code, and value 0 otherwise. Course: Computer Engineering Subject: Logic Circuit and Switch Theory
Draw a register bank with two 4-bit registers. Your design must show SR flip flops,ie, it must show the internals of the individual registers.
Design a 3-bit Shift Left register using D flip-flop. Draw the logic diagram of a 3-bit Shift left register .
A combinational logic circuit that compares between two 2-bit numbers A (A1 A0) and B(B1 B0) is designed. Output F is high when ? > ? and low when ? < ?. 1) Are there any undefined outputs? If there are any undefined outputs what are the inputs?
a) Design a logic circuit with three inputs A, B, C and an output that goes LOW only when A is HIGH while B and C are different. Draw and upload the circuit if you can, or at least describe it in words. b) Which logic gates produce a 1 output in the disabled state? c) Which logic gates pass the inverse of the input signal when these gates are enabled? d) What is the normal resting state of the SET’ and RESET’ inputs of a latch circuit (the prime is same as bar)? What is the active state of each input? e) What is the normal resting state of the NOR latch inputs? What is the active state?
5.10 Implement a 4-bit up counter with T flip flops by doing the following. Up counter means countingfrom 0000 to 1111. Down counter means counting from 1111 to 0000.[1] How many flip flop is needed to implement this counter?[2] Derive a state diadram for this counter.[3] Derive a truth table for this counter with T flip flop[4] Develop state input equations[5] Sketch a logic diagram for this counter.
Construct a 4-bit Serial-In, Parallel-Out (SIPO) register using D flip-flops. Show the circuit diagram and explain how data is shifted in serially and outputted in parallel.
1-Using the Karnaugh Method, design and draw the circuit of the logic circuit that gives the result of the multiplication of the two-bit numbers "AB" and "CD" according to minterms (SOP). Do not make any further simplifications before or after the Karnaugh Method. In tables and Karnaugh, ensure that the least significant bit is on the far right and the entries are sorted alphabetically. Make sure that the circuit you have drawn is understandable, the function you have written and the truth table are readable.