As a designer, you are considering a switch from Al to Cu metal interconnects. Given the resistivity of copper, pcu = 2.2 µ-cm, and the resistivity of aluminum, pai = 3.6 µ-cm. for an interconnect with dimensions: w = 0.250 µm, t = 0.4 µm, 1 = 0.75 mm, and that the oxide thickness is the same as the interconnect thickness: tox = 0.4 µm, with permittivity &ox = 4.2 For each metal, compute the following: a. The sheet resistance Rs, b. The total resistance R, a. The parallel plate capacitance C

As a designer, you are considering a switch from Al to Cu metal interconnects. Given the resistivity of copper, pcu = 2.2 µ-cm, and the resistivity of aluminum, pai = 3.6 µ-cm. for an interconnect with dimensions: w = 0.250 µm, t = 0.4 µm, 1 = 0.75 mm, and that the oxide thickness is the same as the interconnect thickness: tox = 0.4 µm, with permittivity &ox = 4.2 For each metal, compute the following: a. The sheet resistance Rs, b. The total resistance R, a. The parallel plate capacitance C

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

22.Since glass is basically inert, what effects of certain environments are not a problem with optical communications?A. ShrinkageB. CorrosionC. WarpingD. Expansion
Companies designs, creates, and sells Integrated Circuits (chips). What do your buyers useto compare your IC products against your competition’s? Give 3 types of IC benchmarkmeasurements in short answer
High Voltage Engineering Problem A sample of viscoelastic polymer insulation has intrinsic breakdown strength of 2MV/cm, has modulus of elasticity of 0.01 MPa. dielectric constant (relative permittivity) of 3.2 and thickness of 5mm Find out the possibility of electro- mechanical breakdown.
An aluminum wire 7.5m long is connected in parallel with a copper wire 6m long. When a current of 5A is passed through the combination, it is found that the current in the aluminum wire is 3A. If the diameter of the aluminum wire is 1mm, determine the diameter of the copper wire. Assume the resistivity of copper to be 0.017µΩm and that of aluminum to be 0.028 µΩm. Major Topic 7 Factors that affect the resistance
Vbatt=25 VC1=90 ?CC2=75 ?CC3=60 ?CR1=160 ΩR2=120 Ωt2=21.6 msect3=27 msecConsider the circuit shown below which shows a battery connected to some resistors and capacitors along with some switches which will be toggled opened or closed at different times. The components are listed above. The capacitances are in microCoulombs (?C), the resitances are in Ohms (Ω), and the times are in milliseconds (msec). A stopwatch is started at time t1=0 ms. At that time, switch S1 is closed and all other switches are open and the capacitor is allowed to charge up.(a). What is the charge (in uC) on C1 at the time the stopwatch reads t2=21.6 ms?Ans: 1750 uC(b). What is the current (in mA) through R1 at t2=21.6 ms?Ans: 34.9 mA(c). What is the voltage (in V) across R1 at t2=21.6 ms?Ans: 5.58 V(d). What is the voltage (in V) across C1 at t2=21.6 ms?Ans: 19.4 V(e). What is the energy (in mJ) in C1 at t2=21.6 ms?Ans: 17.0 mJThen, immediately at time t2=21.6 on the stopwatch, switch S1 is thrown open and…
A Victoria plaza sub-station supplies 60kW to a load over 250 ft, 100mm2 , two conductors copper feeder, the resistance of which is 0.078 ohm per 100 ft. The bus bar voltage is maintained constant at 600V.Determine the load current
An inter-connect bar is used in a device designed to operate between -20℃ and 60℃. It is 0.5mm long with a cross-sectional area of 0.025 mm2 and has to carry a current of 54 µA when a potential difference of 0.5 V is applied to it. B) The bar is made from silicon doped with acceptor atoms. Calculate the concentration of majority carriers and hence that of the acceptor atoms, assuming that the contribution of the minority carriers is negligible. Determine the minority carrier concentration please solve as soon as possible
Given the schematic below, assume D1 and D2 are silicon with forward voltages of 0.7V. Find the following (with solutions) 1) What input conditions or what value of Vi will allow D1 to conduct? 2) If D1 is conducting, what is V0? Express V0 in terms of Vi 3) Under what conditions will D2 conduct? 4) If D2 is conduciton, what is V0? Express V0 in terms of Vi
Don't copy others work. provide correct solution Question (1)(a) Define homo-structure and hetero-structure devices with appropriate schematic diagram of such structures. (b) Explain the concepts of lattice matched hetero-structure. Sub: Optoelectronics Dept:EEE
Sketch vo for each network and explain your solution.
Design a 1500-meter-long electrical transmission line with a cross-section size of 0.00199 cm2 that can carry a 50-amp current with a power loss of no more than 5 x105 W. Table 1 shows the electrical conductivity of a variety of materials. What kind of material could be a good candidate?
The AC Bridge shown below is used to measure an unknown inductance, Lx and its internal resistance, Rx. The Bridge parameters are R1 = 20,000 ohms, R2 = 50,000 ohms, C2 = 0.003 µf, w = 105 radians per sec. C1 is adjustable from 10 pf to 150 pf, and R3 is adjustable from 0 to 10,000 ohms. At Balance, I. Derive expressions for Rx and Lx in terms of w, R1, R2, R3, C1, and C2. II. Determine the largest values of Rx and Lx that are measurable with the given parameters.