As glycerin flows through a horizontal pipe shown in(Figure 1), the pressure drops 6.5 psi in a 100-ft length.Take pg = 2.44 slug/ft³ and μg = 31.3(10-3) lb-s/ft².Figure▼Part A♥6 in.Determine the shear stress within the glycerin at a distance of 1 in. from the pipe wallExpress your answer using three significant figures.-VE ΑΣΦ It vec71=SubmitPart BRequest Answer72=Find the shear stress along the centerline of the pipeExpress your answer using three significant figures.VD ΑΣΦIt vecBSubmit Request Answer?S1 of 1lb/ft2?lb/ft2

Answered: Image /qna-images/answer/03a3be8b-1e26-44a0-ab80-d14136399ffc.jpg

Answered: As glycerin flows through a horizontal…

As glycerin flows through a horizontal pipe shown in (Figure 1), the pressure drops 6.5 psi in a 100-ft length. Take pg = 2.44 slug/ft³ and μg = 31.3(10-³) lb-s/ft². Figure 6 in. 1 of 1 >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. What is the likelihood that a flow with an average velocity of 0.15 f t/s in a 6 in. water pipe is laminar? Find the speed at which the flow will always be laminar. 2. If the critical Reynolds number for a river is 2000 based on average velocity and depth, what is the maximum speed for laminar flow in a river 10 f t deep? 2 f t deep? Do you expect any river flow to be laminar?.
2.4-2. Shear Stress and Shear Rate in Fluids. Using Fig. 2.4-1, the lower plate is being pulled at a relative velocity of 0.40 m/s greater than the top plate. The fluid used is water at 24°C. a. How far apart should the two plates be placed so that the shear stress t is 0.30 N/m^2? Also, calculate the shear rate. b. If oil with a viscosity of 2.0 x 10^-2 Pa•s is used instead at the same plate spacing and velocity as in part (a), what is the shear stress and the shear rate?
Write the expanded form of Darcy’s Law. Draw a tube full of sand, with piezometers, and label the components of the system.
A shaft with a diameter of D = 80 mm and a length of L = 400 mm, shown in Fig is pulled with a constant velocity of U = 5 m/s the shaft rotates with a constant angular speed of n . = 1450 rpm in a bearing with variable diameter. The clearance between shaft and bearing, which varies from h1 = 1.2 mm to h2 = 0.4 mm, is filled with a Newtonian lubricant whose dynamic viscosity is 0.1 Pa⋅s. Determine the torque required to maintain the motion
Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design a new safety feature for a high-pressure air line in a factory. The air line takes the form of a cylindrical pipe of diameter 150 mm, which is designed to operate between 0.45 MPa and 0.76 MPa. At the end of the pipe a burs9ng disk is placed so that, if the pressure exceeds the maximum opera9ng pressure, the air is vented to atmosphere rather than over-pressuring the chemical reac9on vessel (Figures 4a and 4b). In this ques9on, you should treat the flow as quasione-dimensional and inviscid. The air in the surrounding atmosphere is at 101 kPa and 298 K. a) You have a choice of five disks which can withstand the following forces across them before burs9ng: 10.5 kN, 11.0 kN, 11.5 kN, 12.0 kN, 12.5 kN. Which of these burs9ng disks would you recommend, and why? b) Due to an over-pressurisa9on of the air line, the disk bursts at 9me t = 0. At what pressure in the air line will this occur? c)…
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 10 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer b. Loss of Energy along the straight pipe = Answer J / kg. c. Losing Energy at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement of the pump ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = Answer J / kg. c. Energy Loss at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement for the pump is kg ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
An oil (viscosity 1 Pa.s, density 800kg/m3) is flowing in an axisymmetric pipe. The flow is fully developed and laminar and the velocity at the centre of the pipe is = 30cm/s. The velocity cross-sectional profile is parabolic as: u(r) = U0(1- r2/R2) . Here r is the distance of the point to the pipe centre where the velocity is u(r). . R is radius of pipe (R=4mm). Calculate: the shear stress at the pipe wall the shear stress within the fluid 2 mm from the pipe wall the Reynold’s number of the flow
At a point in a flowing fluid, the shear stress is 3x10-4 psi and thevelocity gradient is 1 s-1. What is the viscosity at this point in SIunits? (1 psi = 6894.76 Pa
Is the Fh equal to the force made on the bolts at flange 1-1 in this question? And can you please plug in the values and the answer so than I can compare with my solution? Please The water flows from the nozzle through a 180-degree elbow. For example, the pipe diameter D-75mm, the nozzle diameter d=25mm, and the pressure gauge at the front of the pipe reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint 1-1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm, the weight of the elbow and the water is 100N, and the acting position is shown in the figure.
A shaft with a diameter of D = 80 mm and a length of L = 400 mm, shown in Fig is pulled with a constant velocity of U = 5 m/s through a bearing with variable diameter. The clearance between shaft and bearing, which varies from h1 = 1.2 mm to h2 = 0.4 mm, is filled with a Newtonian lubricant whose dynamic viscosity is 0.10 Pa⋅s. Determine the force required to maintain the axial movement of the shaft.