As shown in the figure, a rigid beam with negligible weight is pinned at one end attached to two vertical rods. The beam was initially horizontal before the load W = 200KN was applied. Find the vertical movement of W. Given: Regd: A 1.5m B Bronze A = 900 sq.mm E =120 GPa L = 1.2m 3.0 m Vertical movement of W W 2m с Steel A = E = 200 GPa L= W = 200 KN 500 sq.mm 4 m final position

As shown in the figure, a rigid beam with negligible weight is pinned at one end attached to two vertical rods. The beam was initially horizontal before the load W = 200KN was applied. Find the vertical movement of W. Given: Regd: A 1.5m B Bronze A = 900 sq.mm E =120 GPa L = 1.2m 3.0 m Vertical movement of W W 2m с Steel A = E = 200 GPa L= W = 200 KN 500 sq.mm 4 m final position

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Similar questions

The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and CAssume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15If there is a settlement of S at the support C, solve the following using slope deflection method:
As shown in the figure below, a cantilever beam has a span of 6m long. And it is subjected to a concentrated load 6kN acting 4m from the support and a clockwise moment of 30kN.m at the free end. E = 200 GPa and I = 100,000,000 ??^4 . (Use area moment method) a) Determine the deflection at the free end due to concentrated load only. b) Determine the maximum deflection at the free end.
Replace the distributed loading by an equivalent resultant force. Suppose that w1 = 3.4 kN/m and w2 = 2.2 kN/m Specify where the force line of action intersects a vertical line along meme we BC, measured from C Express your answer to three significant figures and include the appropriate units. d=
A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area. The correct answer is 2.84. Show solution.
Use THREE MOMENT EQUATION MET determine the member end moments of the beam of the rectangular cross section shown in Figure 11.10a. Assume that support B settles 2 cm. The modulus of elasticity and the moment of inertia of the beam are E = 210,000 N/mm2 and 4.8 × 104 mm,4 respectively. Hint final answer: MAB= 0 MBA= 165.5127 kn.m MBC= -165.5127 kn.m MCB= 52.2604 kn.m
SHOW COMPLETE SOLUTION Two blocks A and B of weights WA and WB respectively rest on a rough inclined plane and are connected by a short piece of string as shown in the attached figure. If the coefficients of friction between the blocks and the plane are respectively nA = 0.2 and nB = 0.3, find (a) the angle of inclination of the plane for which sliding will impend, and (b) tension in the string.Take WA = WB = 20 N.
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
A wooden beam ( sg= 0.64) is 150 mm by 150 mm by 6m and is hinged at A as shown in the figure. Assuming unit weight of water is 9.79 kN/cu.m. a.) Determine the length of the beam submerged in water? b.) At what angle will the beam float in the water? c.) And determine the buoyant force that causes the beam to be submerged at an angle of theta from horizontal. Please answer this correctly PLEASE :(
Page 605.Consider the Figure9.9 (a)of Concept Problem 9.1,whichis a prismatic cantilever beam with a single load P applied at point A. First, solve theConcept Problem9.1as stated.b.Now let’s add a downward uniformly distributed load of w per unit length and solve the problem. c.With the results of b,assume now thatthe load P points upward. Under thiscase, what iswas a functionofP in order tohavezero displacement at point A?What is the slope at Points Aand B? d.Can you think of a different structure that would have the samedeflection profileas inc, with theappropriate boundary conditions. Explain in detail but concisely.
I rephrased the question so that it can be better understood. The original question is in the picture I have attached. Using the slope and deflection method in structural analysis: Determine the end fixing moments and the central deflection of a built in beam of uniform section of length "L" which carries a load that increases uniformly from zero at each end to "w" per unit length at the centre. End fixing moments answer given: (5/96)wL^2 Central deflection answer given:( 7/3840) wL^4/EI
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
The weights of two children sitting at ends A and B of a seesaw are 84 lb and 64 lb, respectively. Where should a third child sit so that the resultant of the weights of the three children will pass through C if she weighs (a) 60 lb, (b) 52 lb.