As you can see the Ipv4 Cidr block range of Vpc and subnet -1, Which was Created in Aws Console. My question is What CIDR range Should i take for subnet-2 and Subnet-3 As planned to create 3 Subnets inside Vpc . Am i taking right range of Cidr ? Since I am very basic to Aws ,Have no idea . Please explain how could i proceed with this and Why should we take that range?

As you can see the Ipv4 Cidr block range of Vpc and subnet -1, Which was Created in Aws Console. My question is What CIDR range Should i take for subnet-2 and Subnet-3 As planned to create 3 Subnets inside Vpc . Am i taking right range of Cidr ? Since I am very basic to Aws ,Have no idea . Please explain how could i proceed with this and Why should we take that range?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Allow TCP IPv4 192.168.1.21 to firewalld linux command only pls
Linux Command Function ifconfig also: ifcfg, ifup, ifdown, ethtool, nm-tool /etc/init.d/networking restart ip link set down ip link set up The ifconfig command is a tool used to display and configure network interfaces. This command will display information about the network card, IP address, broadcast address, and network mask. It also shows how many packets were received and transmitted. There is also information about the loopback device (lo). ping The ping command allows the user to test whether or not a network connection is active, the speed of that connection, and how a network behaves given specific data loads. arpalso: arping The arp command by itself is used to view the information currently in the ARP table (Address Resolution Protocol). This table maps the IP address of machines on your network segment with their MAC address. hostnamealso: domainname, dnsdomainname The hostname command tells you what the hostname of your machine is set to. The…
Using the Internet Protocol Version 4 (TCP/IPv4) Properties window, change IP address and subnet mask. Save changes. Open command prompt on Windows and type ipconfig. Can you see the IP addresses that you saved? Illustrate and describe the results. Using command prompt on Windows, type ping <your saved IP address>. Illustrate and describe the results. please help me with this
q30- A PC cannot connect to any remote websites ping its default gateway, or ping a printer that is functioning properly on the local network segment. Which action will verify that the TCP/IP stack is functioning correctly on this PC? Select one: A. Download a troubleshooting tool from the PC manufacturer's website B. Use the traceroute command at the command prompt to identify any failures on the path to the gateway C. Use the ping 127.0.0.1 command at the command prompt D. Use the ipconfig /all command at the hosts command prompt E. Use FTP to check for connectivity to remote sites
2. Configure Manual IP address on your Linux Virtual Machine by modifying the network script file for the enp0s3 interface as follows: IPv4: 192.168.x.1 Netmask: 255.255.255.0 Gateway: 192.168.x.254 DNS: 192.168.x.1 X=the last 2 digits of your student ID. If the digits are 01 then use 101 or 02 use 102 etc.
The ___________ command is used to display the full TCP/IP configuration for all adapters for a device. Ping Ipconfig Tracert Ipconfig/all
Linux Command Function ifconfig also: ifcfg, ifup, ifdown, ethtool, nm-tool /etc/init.d/networking restart ip link set down ip link set up The ifconfig command is a tool used to displayand configure network interfaces. Thiscommand will display information about thenetwork card, IP address, broadcast address,and network mask. It also shows how manypackets were received and transmitted. Thereis also information about the loopback device(lo). ping The ping command allows the user to testwhether or not a network connection is active,the speed of that connection, and how anetwork behaves given specific data loads. arpalso: arping The arp command by itself is used to view theinformation currently in the ARP table (AddressResolution Protocol). This table maps the IPaddress of machines on your network segmentwith their MAC address. hostnamealso: domainname, dnsdomainname The hostname command tells you what thehostname of your machine is set to. Thehostname is…
Computer Science Using a for loop, create a ping sweep that records all the IPv4 addresses on your home subnet. You may not use nmap in your code. This is supposed to be a bash script btw.
One of the important steps to change the kali settings to enable internet connection is: Run apatche2 Change ipv4 settings to manual Change IP address settings to DHCP Select Bridge as network adapter
What resource record type defines an IPv6 host address in DNS? Group of answer choices A record AAAA record PTR CNAME record
What type of DNS record directly maps a hostname to an.IP address?A.CNAMEB.AC.MXD.None of the other choicesE.NS
DHCP clients send a DHCPREQUEST packet when they require a new IP configuration.True or False?