The phasor voltage across a certain load is V = 1000 /2 Z30° V, and thephasor current I = 19/2 250° APart ADetermine the power factor.Express your answer using three significant figures.vecPF =percentSubmitPrevious Answers Reguest AnswerX Incorrect; Try AgainPart BDetermine the power.Express your answer to three significant figures and include the appropriate units.P =ValueUnitsSubmitRequest Answer The phasor voltage across a certain load is V = 1000 /2 230° V, and thephasor current I = 19/2 250° A.Part CDetermine the reactive power.Express your answer using three significant figures.Q =VARSubmitRequest AnswerPart DDetermine the apparent power delivered to the load.Express your answer using three significant figures.Vo AEo | i1 vecapparent power =VASubmitRequest AnswerPart EDetermine the impedanceEnter your answer using polar notation. Express argument in degrees.Vo AEo It vec?Z =ΩSubmitRequest Answer

In this question , we will find power factor and power consumption in load...

asor voltage across a certain load is V = 1000/2 Z30° V, and the current I = 19/2 Z 50° A. Part A Determine the power factor. Express your answer using three significant figures. vec PF = percent Submit Previous Answers Reguest Answer X Incorrect; Try Again Part B Determine the power. Express your answer to three significant figures and include the appropriate units. P = Value Units Submit Request Answer

asor voltage across a certain load is V = 1000/2 Z30° V, and the current I = 19/2 Z 50° A. Part A Determine the power factor. Express your answer using three significant figures. vec PF = percent Submit Previous Answers Reguest Answer X Incorrect; Try Again Part B Determine the power. Express your answer to three significant figures and include the appropriate units. P = Value Units Submit Request Answer

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
Please read questions carefully i need power factor and Reactive power of load
What will be the value of the twiddle factor: W42
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
1. Set up the circuit shown using a function generator for the source voltage Vs. Set the function generator to 10 V P-P at 100 Hz (You need to set the Vp-p on the function generator to 5V). Connect the red lead of the scope to VoUT and the black lead to the ground to measure the output or load voltage. 1N4004 Vout Vs 10Vpp 100HZ 1k Ohm 2. Sketch Vout on right, measure the exact peak voltage to the ground on the oscilloscope (use the oscilloscope). DC coupling setting of the 主 Note: Show the results on the screen to your professor to get the signature. V out (Peak) = Vout 3. What is the measured frequency of the load voltage waveform? Frequency f =
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
In the figure: R1 = 1439.170, R2 = R1 and R3 =2R2, then determine the value of the voltage source E. a 8 mA 10 mA 2 mA RT R1 R2 R3 O 25.33 11.51 O 17.27 15.43 13.82 +
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
What is the average Power at maximum resistance? Why? What is the effect to the voltage and current when increasing the load resistance?
%23 IoA 1172 IAB wwww IBC 20L-90°y -J992 204 30°y A ICA IcC a) Find the load current ICA ? b) Give the line yoltoge Vab? C Calculate the total complex power over the saurces of the voltoge7 www