Assignment No. 5 Inductance, Capacitance, and Mutual Inductance Problem 5.1 The current in a 150 µH inductor is known to be i, = 25te-500t A for t > 0. a.) Find the voltage across the inductor for t > 0. (Assume the passive sign convention.) b.) Find the power (in microwatts) at the terminals of the inductor when t = 5 ms. c.) Is the inductor absorbing or delivering power at 5 ms? d.) Find the energy (in microjoules) stored in the inductor at 5 ms. e.) Find the maximum energy 9in microjoules) stored in the inductor and the time (in milliseconds) when it occurs.

Assignment No. 5 Inductance, Capacitance, and Mutual Inductance Problem 5.1 The current in a 150 µH inductor is known to be i, = 25te-500t A for t > 0. a.) Find the voltage across the inductor for t > 0. (Assume the passive sign convention.) b.) Find the power (in microwatts) at the terminals of the inductor when t = 5 ms. c.) Is the inductor absorbing or delivering power at 5 ms? d.) Find the energy (in microjoules) stored in the inductor at 5 ms. e.) Find the maximum energy 9in microjoules) stored in the inductor and the time (in milliseconds) when it occurs.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

elaborate upon the physical process that leads to a capacitor charging and discharging at opposite directions? Don't use Chat GPT otherwise i will dislike u.
The current shown below is applied to a 0.25??capacitor. The initial voltage on the capacitor is zero.a) Find the charge on the capacitor at ?=15??.b) Find the voltage on the capacitor at ?=30??c) How much energy is stored in the capacitor by this current?
The expression for capacitor voltage in an RC circuit (assuming no initial charge) when DC voltage is applied is ??(?) =?s (1 - ?− (t ⁄??) ) Assume Vs = 10 V, C = 50 ??, and R = 100 . Calculate capacitor voltage when t = : 1*RC _____ 5*RC _______ 10*RC ______ 2. The voltage across an inductor when a DC voltage is switched on is ?? (?) ??− ( t ⁄ ?⁄? ). Assume Vs = 10 V, L = 1 mH, and R = 1 Ohm. Find the voltage across the capacitor at t = : 0 ms __________ 1 ms __________ 10 ms __________ Derivation: Consider the equation for ? : ?? = √(1⁄??) − (?⁄2?)2 Oscillation will occur only when this expression is a real number (not an imaginary number). Solving, we see that the expression is a real number when (1 ⁄??)> (?⁄ 2? )2. If C = 0.01 uF capacitance and L = 10 mH, what is the largest value of R for this condition to be true?
The equation for the voltage ?(?) across a capacitor at time ? is?(?)=1?(∫?(?)???0+?0)Where ?(?) is the current passing through the capacitor, and ?0 is the initial charge. Consider a capacitor with ?=1?? and ?0=0. If ?(?)=0.1(0.2+sin0.5?) A, find ?(?) for ?=0.5 sec.
A resistor, an inductor, and a capacitor are connected in parallel to an ac source with voltage amplitude V and angular frequency v. Let the source voltage be given by v = Vcosvt. (a) Show that each of the instantaneous voltages vR, vL, and vC at any instant is equal to v and that i = iR + iL + iC, where i is the current through the source and iR, iL, and iC are the currents through the resistor, inductor, and capacitor, respectively. (b) What are the phases of iR, iL, and iC with respect to v? Use current phasors to represent i, iR, iL, and iC. In a phasor diagram, show the phases of these four currents with respect to v. (c) Use the phasor diagram of part (b) to show that the current amplitude I for the current i through the source is I = √(I2R) + (IC - IL)2 . (d) Show that the result of part (c) can be written as I = V/Z, with 1/Z = √ (1/R2) + [ωC - (1/ωL)]2.
Assignment No. 5 Inductance, Capacitance, and Mutual Inductance a.) Find the voltage across the inductor for t > 0. (Assume the passive signconvention.)b.) Find the power (in microwatts) at the terminals of the inductor when t = 5 ms.c.) Is the inductor absorbing or delivering power at 5 ms?d.) Find the energy (in microjoules) stored in the inductor at 5 ms.e.) Find the maximum energy 9in microjoules) stored in the inductor and the time(in milliseconds) when it occurs.
Find the total capacitance Cab for the given network. (Complete solution and explanation)
2. A parallel plate capacitor with a plate area of 0.13 square meters separated by 1 mm is charged to 9 Volts by a battery, which is then disconnected. The plate separation is then increased to 40 mm.A. Using the expression for the capacitance of a parallel plate capacitor, what do you expect the new potential difference across the plates to be after the increase?B. Suppose you measure the potential difference across the plates after the separation and find it to be 30 V (this should be very different from what you found in part A). This unexpected result can be explained by the effects of “stray capacitance” with nearby objects. Assuming that the stray capacitance can be modeled as a capacitor connected in parallel with the parallel plate capacitor, find the value of this stray capacitance.
Using the 0.68 kilo Ohms, 3.3mH inductance, and 5V source, compute for the theoretical voltages across the resistor and inductor for 10 kHz and 60 kHz. Show the step-by-step computation. Express the voltages in polar form.
Referring to the figure shown, if E=240V, Rs=30k-ohms, Rp=50k-ohms and C=40 micro-farad:(a) To what voltage will the capacitor be charge if the switch is closed for a comparatively long time?(b) Assuming an initial capacitor voltage as in (a) what will be the instantaneous potential ec 1 second after the switch is opened?(c) Assuming the switch to be opened at the instant the capacitor potential reaches the voltage determined in (b), what will be the value of ec 0.5 second after the switch is closed
. A parallel-plate capacitor has a plate separation d and plate area A. An uncharged metallic slabof thickness t is inserted midway between the plates. Determine the:a. Find the capacitance of the device.b. Show that the capacitance is unaffected if the metallic slab is infinitesimally thin.
Capacitance= 5uF1) Determine the time constant of the circuit for the capacities2) For the capacity value, calculate the estimated time to come to the final state.3) Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.