Consider an RLC circuit with resistance 5 ohms, inductance0.05 henrys, capacitance 0.006 farads, and an impressedvoltage, provided by an alternating current generator, ofE(t)=10 sin(25t). At t = 0 the charge is 5 coulomb andthe current is 1 amps.a. Complete the ODE below in terms of the charge in thecircuit Q(t)Q''+Q' +Qb. Solve the ODE and complete the equation for the chargeQ(t) ==

Question b is solved using given initial conditions

Consider an RLC circuit with resistance 5 ohms, inductance 0.05 henrys, capacitance 0.006 farads, and an impressed voltage, provided by an alternating current generator, of 10 sin(25t). At t = 0 the charge is 5 coulomb and the current is 1 amps. E(t) = a. Complete the ODE below in terms of the charge in the circuit Q(t) Q''+ Q' + Q b. Solve the ODE and complete the equation for the charge Q(t) = =

Consider an RLC circuit with resistance 5 ohms, inductance 0.05 henrys, capacitance 0.006 farads, and an impressed voltage, provided by an alternating current generator, of 10 sin(25t). At t = 0 the charge is 5 coulomb and the current is 1 amps. E(t) = a. Complete the ODE below in terms of the charge in the circuit Q(t) Q''+ Q' + Q b. Solve the ODE and complete the equation for the charge Q(t) = =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please provide the complete solution. Topic: Application of DEA circuit has in series of electromotive force given by E(t) = 100 sin 60t V, a resistor of 2 Ω, an inductor of 0.1 H, and a capacitor of 1/260 farads. If the initial current and the initial charge on the capacitor are both zero coulombs, find the charge on the capacitor at any time t > 0.
the emf source, E=3.2 V, of the circuit shown in the figure has negligible internal resistance. the resistors have resistances R1=3 ohm and R2=4.2 ohm. the capacitor has a capacitance C= 3.1uF. A) determine the time constant t , in units of microseconds for charging the capacitor. B) what is the charge Q on the capacitor in units of microcoulomb?
An inductance of 1 H, a resistance of 8 Ω and capacitance of 0.04 F are connected in series with a variable voltage E = 50 sin 3t. Find the current and charge in the system, given the initial conditions q = 0 and l = 0 when t = 0, using method of solution of higher order linear ordinary differential equation.
An electrical circuit contains a resistance R ohms and a capacitor C farads which initially holds acharge Q coulombs. The rate of discharge of the capacitor is given by the equation dQ/dt + Q/RC =0where t is the time in seconds. If R = 80,000 ohms and C = 0·3x 10^-6 farads and also Q = 0·0015coulombs initially, find the equation connecting Q and t. Find Q when t = 0·02 seconds and also twhen Q = 0·001 coulombs
A resistance of 100 Ω, an inductance of 0.1 H, and a capacitance of 5(10−5) F are connected in series.If the total electromotive force is given by 110 sin 377t, such that at t = 0,Q = 0, and i = 0, find thecurrent for t > 0.
Derive an expression for the electrical energy stored in a capacitor of capacitance C when charged to a potential difference V. If C = 2µF and V= 4V, calculate(l.) the final energy stored in the capacitor,(II.) the work done by the battery in the charging process Account for any difference between your answers in parts (I) and (II) above
Consider an LRC series circuit with a resistance of 2.5 ohms, capacitance of 0.1 farad, aninductance of 0.1 henry and electromotive force, volts. Given thatAssume there is no initial charge and no initial current on thecapacitor.The equation of the charge q(t), on the capacitor at any time t q(t)=C1e−5t+C2e−20t+0.05cost+0.2sint . (Do not solve the coefficients). a) State the equation of the current, i(t). b) State the transient and the steady-state current. c) What is the current after a long time.
2. A parallel plate capacitor with a plate area of 0.13 square meters separated by 1 mm is charged to 9 Volts by a battery, which is then disconnected. The plate separation is then increased to 40 mm.A. Using the expression for the capacitance of a parallel plate capacitor, what do you expect the new potential difference across the plates to be after the increase?B. Suppose you measure the potential difference across the plates after the separation and find it to be 30 V (this should be very different from what you found in part A). This unexpected result can be explained by the effects of “stray capacitance” with nearby objects. Assuming that the stray capacitance can be modeled as a capacitor connected in parallel with the parallel plate capacitor, find the value of this stray capacitance.
A current given by i(t)= 3+6 t−−−−−√ (A), where t is measured in seconds, flows through a circuit containing a 14 mF capacitor. Assume the capacitor is initially uncharged. Determine the voltage across the capacitor after 290 ms. Round your answer to 3 significant digits. Value of VC at t= 290 ms is (Volts)
The expression for capacitor voltage in an RC circuit (assuming no initial charge) when DC voltage is applied is ??(?) =?s (1 - ?− (t ⁄??) ) Assume Vs = 10 V, C = 50 ??, and R = 100 . Calculate capacitor voltage when t = : 1*RC _____ 5*RC _______ 10*RC ______ 2. The voltage across an inductor when a DC voltage is switched on is ?? (?) ??− ( t ⁄ ?⁄? ). Assume Vs = 10 V, L = 1 mH, and R = 1 Ohm. Find the voltage across the capacitor at t = : 0 ms __________ 1 ms __________ 10 ms __________ Derivation: Consider the equation for ? : ?? = √(1⁄??) − (?⁄2?)2 Oscillation will occur only when this expression is a real number (not an imaginary number). Solving, we see that the expression is a real number when (1 ⁄??)> (?⁄ 2? )2. If C = 0.01 uF capacitance and L = 10 mH, what is the largest value of R for this condition to be true?
The differential equation for the instantaneous charge q(t) on the capacitor in LRC-series circuit has inductance L = 1 henry, resistance R = 2 ohms, capacitance C = 0.1 farads and external force E(t) = O. Given that there is no initial current and the initial charge is 1 coulomb. a) Find the equation of the charge. (b) Sketch the graph of the charge.
The triangular current pulse shown in the provided figure is applied to a 500 mH inductor. 1. Use passive sign convention. Derive the expression for the inductor energy in Joules at the interval 0 ≤ t ≤ 25 ms in the form w = At^2 + Bt + C Joules, where ^2 refers to "to the power of 2". Provide the value of A in the equation. 2. Derive the expression for the inductor energy in Joules at the interval 25 ms ≤ t ≤ 50 ms in the form w = At^2 + Bt + C Joules, where ^2 refers to "to the power of 2". Provide the value of B in the equation. 3.