help Water flows from a large tank through a large pipe that splits into two smaller pipes,as shown in the figure below. The flow can be considered inviscid and steady state.Assume di = 1.5 cm, d2 = 2 cm, z = 8.5 m, and h = 3.5 m. Determine the level of thetip of the inclined pipe such that the flowrates exiting both small pipes are equal.hdiameter d,diameter d,

Answered: Image /qna-images/answer/ce2ba407-8f9e-44c1-9d67-59c833e9b8df.jpg

Answered: Assume di = 1.5 cm, d2 = 2 cm, z = 8.5…

Assume di = 1.5 cm, d2 = 2 cm, z = 8.5 m, and h = 3.5 m. Determine the level of the %3D tip of the inclined pipe such that the flowrates exiting both small pipes are equal.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Related questions

Q: Q1/ Neglecting losses, determine the discharge in Fig. below

A: Given data: The diameter of the small cavity, d = 4 in. The specific gravity of oil, SGoil = 0.75.…

Q: Problem 3. A siphon, filled with water, is discharging that water. The discharge rate is 2.8 cfs. a)…

A: we have given

Q: Pipes 1, 2, and 3, having diameters of 150 mm, 200 mm, and 250 mm, and leading from reservoifs A, B,…

Q: Reservoirs A, B and C are located atop a hill as shown. Use the formula for headloss: hf = 0.083fsQ?…

Q: Q/ The three water-filled tanks shown in figure are connected by pipes as indicated. If minor losses…

Q: Determine the flowrate through the Venturi meter shown in the figure below if ideal conditions…

A: The velocity of the fluid at point 2 is By using the Bernoulli’s equation the velocity at point 1…

Q: The three-tanks system in figure are interconnected as shown. Compute the flowrate in each pipe,…

A: To find discharge in all pipes

Q: The figure shows a siphon which is used to draw water from a large open tank. If the absolute…

Q: Considering the following figure with flow from A to D, compute the total head loss from A to D if…

A: To Find : The total head loss from A to D and the discharge in each pipe. Given : The discharge is…

Q: Water flows from a main line to a lateral as shown. The flow in the mainline is 1.63 ft3/s.…

Q: An old pipe, 600 mm I.D. and 1219m long, carries medium fuel oil at 30°C from A to B. The pressures…

Q: Elevation = ? reservoir on the right at a rate of 0.45 m/s. The formula for the head losses in the…

Q: (1) A siphon having a diameter d of 100 mm is positioned as shown in the picture. The flow losses…

A: Bernoulli's Equation is based on the conservation of Energy associated with the flowing fluid.…

Q: The discharge through a 180° bend of 50-cm dimeter is 2.5 m /sec. If the pressure at section 1…

Q: Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each…

Q: For the siphon in Figure 21, assume that the volume flow rate is 5.6x10-3m 3 /s. Determine the…

A: Calculated maximum allowable distance Y if the minimum allowable pressure in the system is -18 KPa…

Q: In a hydraulic system, the power is measured as 47.3 X 10-2 Kilo joules per seconds and pressure is…

A: Given , The power (P) = 47.3 x 10-2 Kilo joules per seconds The pressure ( p…

Q: For the pipe system shown. Assume n = 0.013 for all pipes. Neglect minor losses. 1. Compute the…

A: Head loss in a pipe is given by the formula hf = flv22gd = 8 f l Q2π2 g d5Where f= n = 0.013…

Q: he figure shows a siphon discharging oil (sp.gr.= 0.90). The siphon is composed of 75 mm pipe…

Q: 3. Compute the velocity head of the jet if the larger diameter is 100 mm and the smallest diameter…

Q: If the coefficient of Discharge is 0.98 and the theoretical flowrate is 5.5 1/s, calculate the…

A: Write the equation for the coefficient of discharge. Cd =Qact /Qtheortical Hear, The coefficient of…

Q: The discharge pipe of a pump is 400 mm in diameter delivers 0.5m^3/sec of water to a building which…

Q: 7. Water at 10°C is flowing from point A to point B through the fabricated section shown below at…

Q: Water flows in a constant diameter pipe with the following conditions measured: At section (a) p. =…

Q: Q1: If flow rate in pipe shown is (0.5m'/s) find the (H). H. water D=300 mm

A: Given data Volume flow rate = Q = 0.5 m3/sDiameter of pipe = 300 mm = 0.3 m

Q: Question (2) As shown in the Figure below, If the discharge was 0.0035 m/s. Calculate the water…

A: Find the level in the water tank. Given data :- Discharge - 0.0035 m^3/sec.

Q: 28. A large tank contains water to a depth of 1.0 m. Water emerges from a small hole in the side of…

Q: P1 = 735 kPal P2 = 550 kPa 31 mm 19 mm 91 kN/m

A: Given:- Inlet area and throat is: A1= π4d12 = π4×0.0312 =…

Q: 0.99 m 2.8 m 5 cm diameter Group (C) Determine the discharge, the velocity of flow and pressure at…

A: IT is required to determine velocity, flow rate and pressure at point 2

Q: The velocities of flow in a 1 m diameter pipe are 6 m/s on the centerline and 4.85 m/s at x=100 mm.…

A: To find : determine Discharge Given : diameter of pipe d=1m velocity at the centreline vc=6m/s…

Q: 2. For the piping system shown, determine the pressure at point "A", in 10 points Pa, if the head…

Q: Q2: Find the piezometric head at tank (C), if the discharge in pipe (1) = (65 L/sec). Use (-0.025)…

Q: In a hydraulic system, the power is measured as 52 X 10-2 Kilo joules per seconds and pressure is…

Q: Q1: If flow rate in pipe shown is (0.5m/s) find the (H). H. water D=300 mm

Q: Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (∊ = 0.00061 m).…

A: Answer: The pressure at point A is 320.854734 kPa.

Q: Q20/ The pipe flow shown in the Fig. is driven by pressurized air in the tank. What gage pressure P₁…

Q: The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B,…

Q: For the laminar flow of 20°C water in the circular pipe shown find: a) the velocity at r = 4.0 cm.…

Q: Q4) The three water-filled tanks shown in Figure below are connected by pipes as indicated. If minor…

Q: When 0.042 m3 /s of medium fuel oil flows from A to B through 1067 m of new 150-mm uncoated cast…

A: Given:Volume flow rate,Q=0.042 m3/sD=150 mmhead lost, hL=44 mPressure:pB=345 KPazA=0 mzB=18.3 m

Q: 3.7 m 4 cm diameter Group (D) 7.2 m Determine the discharge, the velocity of flow and pressure at…

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A: The equation based on the principle of conservation of mass is called the continuity equation. thus…

Q: Water flows through a horizontal 150mm pipe under a pressure of 414 kPa Assuming no losses, solve…

Q: Problem 4 Show that the quantity of water flowing across a triangular V-notch of angle 20 is Q =…

Q: Q5:- Calculate the discharge of the system in fig.(4),neglecting all losses except through the…

A: There are two types of losses occur in pipe flow:- 1) major loss -these losses are due to viscous…

Q: A pipe drains a tank as shown. If x = 15 ft, y = 5 ft, and head losses are neglected, (a) what is…

A: Given data as per question x = 15 ft y = 5 ft α = 1.0 applying bernaullis…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

help

Water flows from a large tank through a large pipe that splits into two smaller pipes,
as shown in the figure below. The flow can be considered inviscid and steady state.
Assume di = 1.5 cm, d2 = 2 cm, z = 8.5 m, and h = 3.5 m. Determine the level of the
tip of the inclined pipe such that the flowrates exiting both small pipes are equal.
h
diameter d,
diameter d,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. UNKNOWN: DIAMETER OF THE PIPE STRICTLY SHOW COMPLETE FBD AND SOLUTION MUST BE HANDWRITTEN
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
For the pipe system shown. Assume n = 0.013 for all pipes. Neglect minor losses. 1. Compute the head loss from A to B in terms of Q. a. 0.056Q2 b. 0.029Q2 c. 0.016Q2 d. 0.096Q2 2. Assuming Q = 12 cfs, compute the head loss of pipe CD. a. 15.78 ft b. 13.02 ft c. 18.56 ft d. 24.56 ft 3. Assuming Q = 12 cfs, compute the total head loss from A to D. a. 47.786 ft b. 56.673 ft c. 89.451 ft d. 32.562 ft
Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses
Q7. Cavitation just starts to occur in the venturi meter shown in Figure 5 when gage A indicates a pressure of 100 kPa gage. If D = 30 cm and d= 10 cm, what is the water discharge in the system for this condition of incipient cavitation? The atmospheric pressure is 100 kPa gage, and the water temperature is 25°C. Neglect gravitational effects.
Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. Show complete solution no shortcut
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe, the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B.