Assume portion ABC of the rod is made of steel (Ee= 200 GPa , v=0.3) and portion CD is made of aluminum ( E.luminum = 70 GPa, v=0.25). A 1.75 m Area = 800 mm² 120 kN B 1.25 m C Area = 500 mm² 1.5 m 80 kN D 60 kN The deflection of point C is_ The resulting change in diameter of portion AB of the bar is_

Assume portion ABC of the rod is made of steel (Ee= 200 GPa , v=0.3) and portion CD is made of aluminum ( E.luminum = 70 GPa, v=0.25). A 1.75 m Area = 800 mm² 120 kN B 1.25 m C Area = 500 mm² 1.5 m 80 kN D 60 kN The deflection of point C is_ The resulting change in diameter of portion AB of the bar is_

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.5.13P: Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E...

See similar textbooks

Similar questions

A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
-11 Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 40 kips (see figure). The column has an outside diameter d = 4.0 in., wall thickness t = 0.226 in., E = 29,000 ksi, and y = 42 ksi.
An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 500 kN (see figure). The column has an outside diameter d = 200 mm, wall thickness; = 10 mm, E = 200 GPa, and y = 250 MPa.
A hollow steel [E= 30,000 ksi] tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E= 10,000 ksi] rod (2) that has a 2-in.-diameter and a solid 1.375-in.-diameter aluminum rod (3). Determine: (a) the change in length of steel tube (1).(b) the deflection of joint D with respect to the fixed support at A.(c) the maximum normal stress in the entire axial assembly.
Determine the deflection at Point C of the beam shown below (negative is down). P = 16 kN wo = 29 kN/m E = 192 GPa I = 94.145x10-6 m4 Express your answer using three significant figures and ensure that it is in mm.
Question 2: Determine the deflection of D (in inches) with respect to A of the rod shown. Note: Section AC is steel and has a E = 29 x 10^6 psi. Section CD is brass and has E = 14.6 x 10^6 psi.
An axial member consisting of two polymer bars is supported at C. Bar (1) has a cross sectional area of 2720 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 21,560 mm and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C.
Question 2: Determine the deflection of D with respect to A of the rod shown. Note: Section AC is steel and has a E = 29 x 10^6 psi. Section CD is brass and has E = 14.6 x 10^6 psi.